Parts for Kitchenaid KUBL304EBS02: Unit Parts

This drain tray collects and channels wastewater below the dishwasher tub to help keep the cabinet floor dry and prevent water from pooling under the appliance. Replaces a worn or damaged tray to restore proper drainage path. What it does:

• Captures and routes discharged water away from the cabinet base to the dishwasher drain system
• Helps reduce leaks and pooling that can occur from cracks or holes in the original tray
• Works with the dishwasher drain/sump area to maintain proper water flow during cycles
• Can prevent damage to flooring and cabinetry when functioning correctly

• One drain tray

• Disconnect power to the appliance before starting any repair; shut off water if required
• Access typically requires removing the toe kick or lower access panel and tilting or supporting the dishwasher
• Inspect surrounding seals, hose connections and mounting points; replace any damaged parts to prevent future leaks

This thermistor is a temperature-sensing component that monitors conditions inside the refrigerator or freezer compartment. It sends temperature readings to the main control board, which uses that data to regulate the compressor and defrost cycles. Replace this part if your refrigerator is running too warm, too cold, or cycling erratically despite correct thermostat settings.

Rubber grommet for refrigerators. Installs in various cabinet locations to secure components or seal openings. Replace if cracked, missing, or worn.

This electric motor drives the condenser fan located near the compressor at the bottom or rear of the refrigerator. The fan pulls air across the condenser coils to dissipate heat and maintain efficient cooling. Replace this motor if the refrigerator runs warm, the compressor overheats, or you no longer hear the fan running when the compressor is on.

This sealer is a flexible sealing strip used to restore a tight fit where panels or doors meet, helping reduce leaks, drafts and moisture transfer. It replaces worn or damaged seals to help appliances run as intended. What it does:

• Creates a compression seal along a door or panel to prevent air and moisture leakage
• Helps maintain proper temperature control and reduces unwanted drafts
• Stops visible gaps caused by cracked, torn or flattened seal material
• Can reduce short-cycling related to poor sealing by improving the enclosure fit

• Disconnect power and water before starting any repair
• Remove the old seal carefully to avoid damaging surrounding trim or clips
• Clean mating surfaces thoroughly before installing the new sealer for best adhesion and fit
• Some installations require adhesive, retainer clips, or light trimming for a correct fit

Refrigerator won't start or compressor hums without cooling? This capacitor provides the electrical boost needed to start your compressor. DIY-friendly repair.

Back cover panel for refrigerator interior. Installs on rear wall to conceal components. Replace if cracked, broken, or missing for a clean look.

This is the electrical power cord that connects the refrigerator to the wall outlet, supplying electricity to the unit. It includes the plug and wiring needed to deliver the correct voltage to the appliance. Replace this cord if it is frayed, damaged, has exposed wiring, or if the refrigerator intermittently loses power due to a faulty connection.

This drier tube is a component in the refrigerator's sealed refrigeration system that removes moisture from the refrigerant as it circulates. It helps prevent ice blockages that can restrict refrigerant flow and reduce cooling performance. Replace if the refrigerator is not cooling properly, runs continuously, or a technician has diagnosed a moisture-related restriction in the sealed system.

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.