Parts for Ge JBS86SP5SS: Upper Door Parts

This handle and end cap assembly replaces a worn or damaged refrigerator door handle end for a clean, finished appearance and secure grip. Restores proper handle alignment and lets the door open and close smoothly. What it does:

• Replaces a damaged or cracked handle end cap and attached handle section
• Restores a secure grip and proper door operation
• Improves door appearance by replacing scratched or dented stainless pieces
• Helps eliminate looseness, wobble, or misalignment at the handle end

• One handle and end cap assembly (stainless), as shown

• Disconnect power or follow appliance safety procedures before starting work
• Typical installation uses basic hand tools; handle attaches to door with screws/fasteners
• Align assembly carefully and tighten fasteners snugly—do not overtighten to avoid stripping

This right-side door trim bracket secures the exterior trim to the appliance door, restoring a flush, finished appearance and preventing the trim from coming loose. Designed to replace a damaged or missing right-hand bracket. What it does:

• Holds the door trim in place on the right side to maintain alignment and appearance
• Prevents trim gaps, vibration noise, and rattling caused by a loose or broken bracket
• Restores proper trim attachment after collision, wear, or failed fasteners
• Works with the factory trim assembly to ensure a straight, secure fit

• One right-side door trim bracket

• Use basic hand tools; retain any reusable screws or clips unless damaged
• Power off and unplug the appliance before starting work for safety
• Align the bracket and trim before tightening fasteners to avoid cracking the trim
• Replace missing or damaged clips or screws with OEM-specified fasteners

This left-hand door handle bracket secures the refrigerator door handle to the door, restoring a stable grip and proper handle alignment. Durable replacement part helps stop a loose or wobbly handle and keeps the door operating smoothly. What it does:

• Mounts the door handle to the left side of the refrigerator door
• Provides a secure anchor to prevent handle movement or sagging
• Restores proper handle alignment for comfortable opening and closing
• Helps eliminate rattling or looseness when the door is used

• One left-hand door handle bracket

• Designed for direct replacement; inspect mounting screws and handle for wear before installing
• Use basic hand tools; avoid overtightening fasteners to prevent cracking the bracket
• Disconnect power only when working near electrical components; follow appliance safety guidance
• If screws or handle hardware are missing or damaged, replace those parts as well

This oven door insulation is the internal pad that sits inside the oven door to help limit heat loss and reduce the door exterior temperature. It restores the door's thermal barrier for more consistent oven performance. What it does:

• Replaces worn or damaged insulation that can allow heat to escape from the oven cavity.
• Helps the oven maintain set temperatures and can reduce extended cook times caused by heat loss.
• Lowers the temperature felt on the exterior door by restoring the internal thermal layer.
• Fits inside the oven door assembly and works with the door glass and inner liner to form the door's insulation package.

• Disconnect power to the appliance and allow the oven to fully cool before beginning.
• Remove the oven door and inner door liner per the manufacturer instructions to access the insulation.
• Wear gloves and a dust mask when handling old insulation; avoid compressing or folding the new pad during installation.
• Reassemble door components securely before use.

This Oven Door Gasket forms a heat-resistant seal between the oven door and the front frame. Replacing a worn seal helps your oven preheat efficiently, hold temperature more consistently, and keep heat and spills contained.

• Creates a perimeter seal to retain heat and support even baking
• Helps reduce long preheat times and noticeable temperature swings
• Replace if the gasket is torn, frayed, hardened, flattened, or leaking heat around the door
• Restores proper door closure feel and uniform contact

• Disconnect power and allow the oven to cool completely before servicing.
• Open the door and remove the old gasket by releasing it from its existing mounting points.
• Install the new gasket into the same points without stretching; ensure an even seal around the full perimeter before use.

This is the upper outer door panel for select GE refrigerators, a direct-fit replacement that restores the appliance's exterior appearance and protection. Stainless finish matches factory styling. What it does:

• Replaces a damaged, dented or scratched upper outer door panel to restore appearance
• Protects internal door components and insulation from impact and wear
• Helps ensure a proper seal and alignment when paired with the correct inner door and hardware
• Intended for use only on compatible models; prevents further cosmetic deterioration

• Includes 1 upper outer door panel (stainless)

• Disconnect power and empty door shelves before starting; handle panel carefully to avoid scratches
• Retain and reuse original mounting hardware when possible; replace any damaged clips or screws
• Do not attempt modifications; use only on compatible refrigerator models

Upper window pack assembly that replaces a cracked or damaged refrigerator door window panel, restoring appearance and helping protect the components behind the outer window. What it does:

• Replaces the upper door window pack to restore a clear, finished exterior on the appliance door.
• Addresses visible damage symptoms such as cracked, scratched, cloudy or broken window panels.
• Protects internal door components from exposure to moisture and debris.
• Matches the OEM-style mounting points for a like-for-like replacement when used with the correct model parts.

• Disconnect power and remove food from the door area before starting any repair.
• Handle the window pack carefully; wear cut-resistant gloves and eye protection when removing broken or cracked pieces.
• Remove any trim or fasteners per the appliance's service instructions; retain mounting screws and gaskets as needed.
• Refer to the OEM service manual or diagram for model-specific removal and reassembly steps.

This is a replacement screw used to secure panels and components on compatible appliances. It provides a direct-fit fastening solution to restore proper part alignment and prevent rattling or loose panels. What it does

• Fastens appliance panels, brackets or assemblies where an 8-18 x 5/8 screw is specified
• Replaces missing or stripped fasteners that allow parts to shift or vibrate
• Restores secure mounting for components to reduce noise and movement
• Useful when a factory screw is damaged, corroded, or lost during service

• One screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver size and type to avoid stripping the head
• Install by hand first, then snug with a driver—do not over-torque
• Keep removed hardware organized to ensure correct reassembly