Parts for Ge ZET2FL2SS: Upper Doors Parts

This SCR (silicon controlled rectifier) is a replacement power-regulation semiconductor used in select GE appliances to control voltage to heating elements or motors, restoring reliable variable power control and stable operation. What it does

• Regulates and switches power to heating elements or drive motors as part of the appliance's control circuitry.
• Helps maintain consistent heat or motor speed when the control board calls for variable output.
• Can resolve symptoms such as intermittent heating, fluctuating motor speed, or appliances that run only on certain settings.
• Functions as a direct electrical switching component—not a user-serviceable interface.

• One SCR (silicon controlled rectifier) matching OEM part WB01X24096.

• Always disconnect power at the breaker or unplug the appliance before starting any repair.
• Handle the part carefully; observe anti-static precautions and avoid touching leads or terminals.
• Verify the part number on the old component matches WB01X24096 before installation.

This 8-32 machine screw (7/16") is a painted fastener used to secure panels, brackets, and components on compatible appliances. It replaces missing or worn screws to restore proper fit and reduce vibration. What it does:

• Secures panels, control assemblies, brackets, and small hardware
• Restores proper alignment and prevents rattling or loose parts
• Used where an 8-32 thread and 7/16" length are required
• Painted finish matches appliance surfaces and resists corrosion

• One painted 8-32 machine screw, 7/16" length

• Unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or nut driver to avoid stripping the head
• Install by hand to start threads, then tighten snugly—do not overtighten
• Keep track of small parts during disassembly; magnetic trays help prevent loss

This replacement screw is a simple fastener used to secure panels, trim, and internal components on GE appliances, restoring proper fit and preventing loose parts. It's a direct-replacement hardware piece for common mounting and assembly points. What it does

• Secures panels, brackets, and trim to prevent rattling or gaps
• Replaces missing, stripped, or corroded fasteners that compromise fit
• Helps maintain proper alignment of controls and components
• Keeps internal parts fixed for safe, reliable operation

• Screw as shown

• Unplug or disconnect power to the appliance before starting repairs
• Use the correct screwdriver or bit to avoid stripping the head
• Install with moderate torque; do not overtighten to prevent thread or component damage
• If threads are damaged or the mating hole is stripped, replace the mating hardware or repair the thread before reuse

This is a genuine replacement mounting screw designed to secure components and panels on compatible GE appliances, restoring proper fit and reducing rattles or loose parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens and secures appliance panels, brackets, or small components
• Restores proper alignment and reduces vibration or rattling noises
• Replaces missing, worn, or damaged screws that prevent secure assembly
• Simple, low-cost solution to loose or shifting parts

• Turn off and unplug the appliance before servicing to avoid electrical shock
• Use the correct driver to avoid stripping the screw head; match thread engagement carefully
• Do not overtighten — snug until secure to prevent damage to parts or threads

A single #8-18, 1/2-inch screw used to secure interior and exterior appliance panels and components. Replaces a worn or missing fastener to restore secure mounting and reduce rattles or loose parts. What it does:

• Fastens panels, trim, brackets, and small components where a #8-18, 1/2" screw is required
• Replaces missing or stripped screws that cause loose panels or vibration noise
• Provides a proper threaded connection for reliable mechanical support
• Matches common OEM panel and trim fastening points

• Unplug the appliance or shut off power before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid over-tightening, which can strip threads or crack panels
• If thread engagement is damaged, replace the mating fastener or insert as needed