Parts for Bosch DKE9405MUC/01: Vent Hood Parts

This is a fan motor that is installed inside several range hoods. It is located inside the hood and helps ensure the fan operates correctly. As a part of the fan, this motor helps filter smoke and other contaminants in the kitchen air to the outside of the home. It removes fumes, greases, steam, and heat from the air. If the fan is no longer operating on a range hood, this could be the result of a damaged fan motor. If that's the case, the component will need to be replaced.First, make sure the range hood is unplugged or the circuit breaker has been turned off. Remove the bottom panel and filters from the appliance. Take off the side panels and pull the range hood down from the cabinet. The fan blade will need to be removed to access the fan motor. Take out the old motor and install the replacement part before reassembling the range hood for use.The fan motor is sold as an individual item. It is a genuine OEM replacement component that is sourced directly from the manufacturer. This part is made for use with range hoods made by Bosch and Thermador.

A replacement power transformer that supplies the control board with the low-voltage power it needs to operate. Restores proper control function and helps resolve power-related control failures. What it does

• Converts incoming mains voltage to the low-voltage supply used by the appliance control board.
• Commonly replaces a failed transformer when the control board loses power or behaves intermittently.
• Can stop symptoms such as a dead control panel, unresponsive buttons, or intermittent operation when caused by a failed transformer.
• Works as the electrical interface between the main power and the appliance's electronics.

• Disconnect power to the appliance before starting any repair to avoid shock risk.
• Handle wiring carefully and match connectors/terminals exactly; take a photo before disconnection for reference.
• Requires basic hand tools; mounting screws and connector retainers should be reused unless damaged.

This electronic control module manages a dishwasher's cycle sequencing and user controls so the appliance runs the selected wash programs correctly. Replaces a failed control board to restore normal operation and control response. What it does:

• Governs wash cycles, timing, and control logic for the appliance
• Processes input from touchpad/controls and sends commands to valves, pumps, and heaters
• Can cause unresponsive buttons, failure to start, or stuck cycles when faulty
• May trigger error codes or prevent cycle advancement if damaged

• One control module (electronic control board)

• Disconnect power at the breaker before starting any work
• Access usually requires removing the control panel or console; follow OEM service instructions
• Handle the board by the edges and avoid static discharge

The Capacitor is an OEM part for Bosch vent hoods. This part temporarily stores electrical energy to generate stable high voltage for halogen light operation.

Situated near the light ballast, the capacitor traps charges that build up after each discharge then holds them for instantaneous delivery during the next bulbs ignition. This allows continuous high-frequency halogen lighting for enhanced visibility over cooktops.

Symptoms of a faulty capacitor include:

• Dim or flickering halogen lights failing to illuminate as intended
• Buzzing noises or humming from internal components
• Lights refusing to trigger on or operating intermittently
• Tripped circuit breakers due to capacitor malfunction

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Halogen Lamp is an OEM component specifically designed for select Bosch downdraft ventilation hoods. As an illumination source, it provides sufficient light for safe nighttime cooktop use.

Toughened outer casings protect encased bulbs against accidental breakage. Ventilated globe designs dissipate heat for prolonged lamp life while avoiding premature degradation.

Causes requiring replacement relate to cumulative burning hours expended. Direct physical impacts could also crack protective glass allowing water damage that accelerates filament failure. 

Symptoms of a bad lamp include:

• Diminished lighting failing to sufficiently illuminate cook surfaces   
• Flickering or inability to power on through expected lifecycles
• Broken housing fragments exposing live connectors to short circuits

This OEM Bosch replacement halogen lamp is also compatible with Thermador, Gaggenau, and some Kenmore range hoods employing self-contained lighting solutions. Proper bulb installation will restore intended visibility for safe evening meals.
 

This metal mesh filter traps grease and cooking residues to protect the blower and ductwork in your vent hood. Replacing a clogged or damaged filter helps maintain airflow and keeps the hood operating efficiently.

• Captures airborne grease from cooktop fumes to keep internal components cleaner
• Helps maintain proper ventilation and reduce odors
• Common signs it's time to replace: saturated mesh, visible damage/warping, or persistent grease buildup and reduced suction
• Easy to access for routine cleaning or swap-out

• Disconnect power to the hood before service
• Allow the hood and any nearby cooking surfaces to cool completely
• Release the filter latch/handles and slide the old filter out; install the new filter in the same orientation
• Do not operate the hood without all filters securely in place

This halogen light bulb restores bright, reliable illumination in your appliance so you can clearly see the cooking area or interior. Replace a burned-out or flickering bulb to maintain visibility and safe operation. What it does:

• Provides illumination inside the appliance or over the cooking surface
• Replaces a failed halogen lamp to restore proper lighting
• Typical symptoms: light won't turn on, is dim or flickers, or works intermittently
• Helps you monitor food and check progress without guesswork

• 1 halogen lamp

• Disconnect power/unplug and allow the bulb and surrounding area to cool completely before service
• Access the lamp per your model's instructions; remove any lens or cover carefully
• Handle the new halogen bulb with gloves or a clean cloth; avoid touching the glass capsule
• Match the bulb type and rating specified for your model; do not exceed the rated wattage