Parts for Bosch HMV3052U/01: Vent Parts

This is a charcoal filter used in over-the-range microwaves to remove odors and smoke when the microwave is set to recirculate air rather than vent outside. The filter traps grease and odor particles from cooking fumes. Replace it if you notice persistent cooking odors, reduced air filtration performance, or if the filter appears visibly saturated or discolored.

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or corroded screws used to secure panels, brackets, or hardware.

This temperature regulator is the refrigerator thermostat that senses and controls interior temperature, helping the appliance maintain set cooling levels for food preservation. It replaces a faulty regulator to restore reliable temperature control. What it does:

• Detects cabinet temperature and signals the compressor/cooling system to cycle on or off
• Helps stop temperature drift, long run cycles, or overly warm compartments when failing
• Common symptom linkage: fridge or freezer not reaching or maintaining set temperature
• Works as the control interface between the user temperature setting and the cooling system

• One temperature regulator

• Always disconnect power before inspecting or replacing the thermostat to avoid shock
• Note wire locations or take a photo before removal to ensure correct reassembly
• Verify wiring connections and secure mounting; test operation after restoring power

This replacement lamp restores proper lighting in your appliance, making it easier to see contents and monitor cycles. Install it when the original bulb burns out or flickers to bring clear, reliable illumination back.

• Provides illumination when the appliance's light circuit or door switch activates
• Common symptoms: no light, intermittent or flickering light, or a visibly failed bulb
• Heat, age, vibration, or moisture can cause the lamp to fail
• A new lamp typically resolves lighting issues if the socket and switch are sound

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool fully before opening the light cover
• Handle the glass with clean gloves or a cloth to avoid skin oils
• Install the exact replacement specified for your model; do not exceed the manufacturer's rating

Holds the bulb and provides electrical connection for interior lighting. Replace if cracked, heat-damaged, or loose causing lights to fail. Confirm fit.

This replacement screw secures appliance panels and components at their mounting points. Swap in a new screw to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded.

• Fastens the designated panel, bracket, or component in place
• Replaces a missing, stripped, or rusted screw
• Helps address loose panels, gaps, rattling, or misalignment at the mounting point
• Maintains proper assembly integrity after service or vibration

• Disconnect power; shut off water supply if working near plumbing
• Match to the removed fastener and replace one at a time to preserve alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly and avoid overtightening, especially into plastic or thin sheet metal

Replacement mounting screw for microwave panels and brackets. Secures components, eliminates rattling from loose panels, and restores proper fit.

This motor start/run capacitor helps the appliance's motor start smoothly and run more efficiently. Replacing a failing capacitor can restore normal motor operation and reduce humming or intermittent motor stops. What it does:

• Provides the temporary energy boost the motor needs to start and maintain proper speed.
• Commonly linked to symptoms such as motor humming, slow motor start, or motors that stall or run inconsistently.
• Works with the motor's starting circuit to stabilize performance during load changes.
• Matches the original function and electrical role of the factory-installed capacitor when replaced with the correct part number.

• One capacitor as shown.

• Disconnect power to the appliance before attempting any repair.
• Discharge the capacitor safely (use insulated tools and follow manufacturer procedures) to avoid electrical shock.
• Replace only with a capacitor that matches the original specifications and mounting.

Microwave won't start or trips the breaker? This circuit protection fuse opens during overloads or shorts to protect components. Easy fix after resolving cause.

This is an electrical noise filter module that mounts inside the microwave cabinet. It filters out electromagnetic interference generated by the microwave's components to prevent disruption to other nearby electronics. Replace this part if the microwave trips a breaker, fails to start, or causes interference with other appliances.

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or damaged screws that secure panels, brackets, or components.

Microwave won't power on or loses power intermittently? This power harness cable replaces damaged wiring between controls and components. Quick fix.