Parts for Jenn-Air JXD7030YS0: 01 - Ventilation Parts

Fix weak or no ventilation in your downdraft system with this blower motor. Restores proper airflow and suction. Moderate DIY repair, 1-2 hours.

This is a grease filter designed for range downdraft ventilation systems. It captures grease and airborne particles produced during cooking, preventing them from entering the vent ductwork. Replace this filter if it is visibly clogged with grease, airflow from the downdraft vent has decreased, or you notice smoke and odors lingering in the kitchen during cooking.

This is a vent filter designed for use in a range hood or downdraft ventilation system. It captures grease, smoke, and airborne particles generated during cooking to keep your kitchen air clean. Replace this filter if it appears heavily discolored with grease buildup, if cooking odors are no longer being effectively filtered, or if airflow from the vent seems reduced.

Fix unresponsive hood controls with this control button replacement. Restores fan speed and light settings. Typical 15-minute repair for most models.

This front cover replaces the damaged or worn outer front panel on compatible dryers, restoring the appliance's appearance and protecting internal components. It provides a clean mounting surface for the door and controls. What it does

• Shields internal parts from lint, dust, and impact damage to help maintain dryer performance.
• Restores a secure mounting surface for the door and related hardware so the door seals and closes properly.
• Stops rattling or vibration caused by cracked or loose front panels.
• Improves the dryer's appearance if the original cover is dented, cracked, or rusted.

• High-level replacement: remove the door, disconnect power, and unfasten screws to swap the front cover; reassemble in reverse order.
• Always disconnect the appliance from power (and gas supply for gas dryers) before beginning service.
• Keep track of fasteners and any clips removed—some models reuse the same hardware.
• If rust or corrosion is present on mounting points, inspect and address before installing the new cover.

This is a push button switch assembly used on a range hood or downdraft ventilation system to control fan speed or lighting functions. The assembly includes the switch mechanism and its cover. Replace this part if the buttons are unresponsive, stuck, cracked, or if the ventilation fan or lights no longer turn on or off when pressed.

Fix a downdraft vent that won't turn on or respond to controls with this replacement control switch. Common repair for unresponsive downdraft systems.

This arm motor powers the dishwasher spray arm, restoring rotation needed for even cleaning and proper water circulation. Replace a failed motor to stop arm stalling or noisy operation and recover normal wash performance. What it does:

• Spins the spray arm so water sprays across dishes for effective cleaning.
• Works with the wash/circulation assembly to maintain proper water flow.
• Common symptoms: spray arm not rotating, uneven cleaning, motor humming or noisy during the wash cycle.
• Replaces worn or failed arm motor that causes intermittent or no rotation.

• Disconnect power to the appliance before beginning any work.
• Handle the motor and mounting hardware carefully; wear gloves and eye protection.
• Verify alignment of the motor coupling and spray arm during installation; ensure fasteners are tightened to spec.
• After installation, run a short cycle to check for leaks.

Replace your range hood damper if the original is cracked, broken, or missing. This damper installs inside the ventilation system to control airflow.

Replace a broken or missing switch cover on your downdraft ventilation system. This access panel cover secures the control switch assembly for safe operation.

This is a push button switch assembly used on a range hood or downdraft ventilation system to control fan speed or lighting functions. The assembly includes the switch mechanism and its cover. Replace this part if the buttons are unresponsive, stuck, cracked, or if the ventilation fan or lights no longer turn on or off when pressed.

Blower fan evacuates cooking fumes and odors from your downdraft system. Replace if ventilation weakens or noise increases. Verify fit with your model.

Hood controls unresponsive or not working? This electronic control board manages cycle selection, timing, and signals to restore reliable operation.

Decorative trim for downdraft ventilation systems. Replaces cracked, chipped, or worn trim pieces that detract from your kitchen's appearance.

Replacement spring for downdraft ventilation systems. Installs in the lifting mechanism. Needed when the original spring is broken, stretched, or missing.

This push-button switch mounts in the control area and completes the circuit when pressed, allowing the appliance to start or change a function. Replacing a worn switch restores reliable button response and consistent operation.

• Closes/opens the electrical circuit when the button is pressed and released
• Helps control on/off or specific functions, depending on the appliance design
• Common symptoms: no response to button presses, intermittent operation, or having to press unusually hard
• Physical signs of failure can include a stuck button, broken tabs, or damaged terminals

• Disconnect power to the appliance before servicing
• Access the control area; note wire locations and terminal markings on the original switch
• Transfer connectors one at a time to the new switch; secure the switch in its bracket or panel
• Reassemble, restore power, and test button operation

Replace a broken or missing switch cover on your downdraft ventilation system. This access panel cover secures the control switch assembly for safe operation.

This is a push button switch assembly used on a range hood or downdraft ventilation system to control fan speed or lighting functions. The assembly includes the switch mechanism and its cover. Replace this part if the buttons are unresponsive, stuck, cracked, or if the ventilation fan or lights no longer turn on or off when pressed.

Fix a downdraft vent that won't raise or lower with this motor arm. Restores smooth up-and-down operation. Moderate DIY repair with basic tools.

Replacement retaining clip for downdraft ventilation systems. Secures components and trim pieces in place. Replace if damaged, cracked, or missing.

Secure downdraft ventilation panels and trim to eliminate rattles and maintain proper alignment. Replace when clips break or lose tension. Confirm fit with your model number before ordering.

If exhaust odors linger when your range hood is off, this damper assembly restores proper vent control. Opens and closes to prevent backdrafts.

Genuine mounting screw for downdraft ventilation systems and range hoods. Secures panels and brackets. Replace if missing, stripped, or worn.

Factory screw secures panels and components in your downdraft ventilation system. Replace missing, stripped, or damaged screws to restore tight fit.

Decorative trim panel for downdraft ventilation systems. Installs on the exterior housing for a finished look. Replace if cracked, damaged, or missing.