Parts for Kitchenaid KXD4630YSS0: 01 - Ventilation Parts

Fix weak or no ventilation in your downdraft system with this blower motor. Restores proper airflow and suction. Moderate DIY repair, 1-2 hours.

Removes smoke, grease, and odors from your downdraft ventilation system. Replace when clogged or damaged to maintain airflow. Confirm fit with your model.

This replacement grease filter traps cooking grease and airborne particles as your microwave's vent runs. Replacing a clogged or damaged filter helps maintain airflow, protect the blower and ductwork, and keep the area under the unit cleaner. What it does:

• Traps grease and particulates from cooktop fumes during venting
• Helps maintain proper airflow through the vent system
• Protects the fan/motor and interior ducting from buildup
• Common symptoms: weak venting, visible grease buildup, lingering smoke, or a torn/warped filter

• 1 grease filter

• Disconnect power to the appliance before service
• Access the filter from the underside; release the retaining tab or screws (varies by model)
• Slide out the old filter and seat the new one fully and securely
• Do not operate the vent/microwave without a filter installed

Fix unresponsive hood controls with this control button replacement. Restores fan speed and light settings. Typical 15-minute repair for most models.

This front cover replaces the damaged or worn outer front panel on compatible dryers, restoring the appliance's appearance and protecting internal components. It provides a clean mounting surface for the door and controls. What it does

• Shields internal parts from lint, dust, and impact damage to help maintain dryer performance.
• Restores a secure mounting surface for the door and related hardware so the door seals and closes properly.
• Stops rattling or vibration caused by cracked or loose front panels.
• Improves the dryer's appearance if the original cover is dented, cracked, or rusted.

• High-level replacement: remove the door, disconnect power, and unfasten screws to swap the front cover; reassemble in reverse order.
• Always disconnect the appliance from power (and gas supply for gas dryers) before beginning service.
• Keep track of fasteners and any clips removed—some models reuse the same hardware.
• If rust or corrosion is present on mounting points, inspect and address before installing the new cover.

Fix a damaged or missing switch cover on your downdraft vent. This protective cover shields the switch assembly from debris and keeps it secure.

Fix a downdraft vent that won't turn on or respond to controls with this replacement control switch. Common repair for unresponsive downdraft systems.

This arm motor powers the dishwasher spray arm, restoring rotation needed for even cleaning and proper water circulation. Replace a failed motor to stop arm stalling or noisy operation and recover normal wash performance. What it does:

• Spins the spray arm so water sprays across dishes for effective cleaning.
• Works with the wash/circulation assembly to maintain proper water flow.
• Common symptoms: spray arm not rotating, uneven cleaning, motor humming or noisy during the wash cycle.
• Replaces worn or failed arm motor that causes intermittent or no rotation.

• Disconnect power to the appliance before beginning any work.
• Handle the motor and mounting hardware carefully; wear gloves and eye protection.
• Verify alignment of the motor coupling and spray arm during installation; ensure fasteners are tightened to spec.
• After installation, run a short cycle to check for leaks.

Replace your range hood damper if the original is cracked, broken, or missing. This damper installs inside the ventilation system to control airflow.

Replace a broken or missing switch cover on your downdraft ventilation system. This access panel cover secures the control switch assembly for safe operation.

Fix a damaged or missing switch cover on your downdraft vent. This protective cover shields the switch assembly from debris and keeps it secure.

Blower fan evacuates cooking fumes and odors from your downdraft system. Replace if ventilation weakens or noise increases. Verify fit with your model.

Hood controls unresponsive or not working? This electronic control board manages cycle selection, timing, and signals to restore reliable operation.

Decorative trim that covers the control panel edge on downdraft ventilation systems. Replaces cracked, damaged, or worn trim for a clean, finished look.

Decorative trim piece for downdraft ventilation systems. Covers edges and provides a finished look. Replace if cracked, chipped, or discolored.

Replacement spring for downdraft ventilation systems. Installs in the lifting mechanism. Needed when the original spring is broken, stretched, or missing.

This push-button switch mounts in the control area and completes the circuit when pressed, allowing the appliance to start or change a function. Replacing a worn switch restores reliable button response and consistent operation.

• Closes/opens the electrical circuit when the button is pressed and released
• Helps control on/off or specific functions, depending on the appliance design
• Common symptoms: no response to button presses, intermittent operation, or having to press unusually hard
• Physical signs of failure can include a stuck button, broken tabs, or damaged terminals

• Disconnect power to the appliance before servicing
• Access the control area; note wire locations and terminal markings on the original switch
• Transfer connectors one at a time to the new switch; secure the switch in its bracket or panel
• Reassemble, restore power, and test button operation

Replace a broken or missing switch cover on your downdraft ventilation system. This access panel cover secures the control switch assembly for safe operation.

Fix a damaged or missing switch cover on your downdraft vent. This protective cover shields the switch assembly from debris and keeps it secure.

Fix a downdraft vent that won't raise or lower with this motor arm. Restores smooth up-and-down operation. Moderate DIY repair with basic tools.

Replacement retaining clip for downdraft ventilation systems. Secures components and trim pieces in place. Replace if damaged, cracked, or missing.

Secure downdraft ventilation panels and trim to eliminate rattles and maintain proper alignment. Replace when clips break or lose tension. Confirm fit with your model number before ordering.

Hardware kit for downdraft ventilation systems. Includes mounting screws, bolts, and fasteners to secure unit during installation or replacement.

If exhaust odors linger when your range hood is off, this damper assembly restores proper vent control. Opens and closes to prevent backdrafts.

Genuine mounting screw for downdraft ventilation systems and range hoods. Secures panels and brackets. Replace if missing, stripped, or worn.

Factory screw secures panels and components in your downdraft ventilation system. Replace missing, stripped, or damaged screws to restore tight fit.

Decorative trim for downdraft ventilation systems. Replaces cracked, chipped, or discolored trim pieces that affect the finished appearance of your unit.