Parts for Kenmore 417.99165830 (41799165830, 417 99165830): Washer Drive System, Pump Parts

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Rubber bushing that cushions and supports the washer tub assembly. Replace if worn, cracked, or causing excessive vibration during the spin cycle.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. While this might seem like a difficult repair, replacing the pump and motor assembly is a fairly simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Proceed to remove the upper dishrack from its track.After that, release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly and follow the previous steps in reverse to reconfigure the dishwasher.This genuine OEM part is compatible with is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand dishwashers.

Red

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

This cable tie secures wiring and small hoses inside the appliance to prevent rubbing, snagging, and vibration-related movement. It's a simple replacement part for restoring proper wire routing and keeping components tidy and safe. What it does:

• Holds wiring harnesses and loose cables in place to reduce wear and chafing
• Helps prevent wiring from contacting hot or moving parts
• Reduces noise caused by loose wires or hoses
• Keeps connectors and lines routed for reliable operation

• Disconnect power to the appliance before servicing
• Route wiring as shown in the appliance wiring diagram or photos, then cinch the tie snugly—do not overtighten
• Trim excess tail and ensure the tie does not stress the wire insulation
• Replace any damaged wiring or insulation discovered during installation

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.