Parts for HLP21N: Washer Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This tapping screw is a self-tapping fastener used to secure panels and components on compatible appliances, restoring secure mounting and preventing loose or vibrating parts. It's a direct replacement for a single factory screw. What it does:

• Threads into sheet metal or plastic mounting points to hold panels, brackets, or small components
• Replaces missing or stripped screws that cause loose panels or rattling
• Helps restore proper alignment and secure connections for controls and covers
• Works where a self-tapping fastener is required instead of a machine screw

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid cam-out and head damage
• Start threading by hand to ensure proper engagement, then tighten until snug — do not over-torque
• Replace only with the exact part to ensure fit and proper fastening

This water valve absorption gasket is a replacement seal that fits between the water valve and surrounding housing to maintain a watertight connection and prevent leaks. It restores a secure seal for proper valve operation and leak control. What it does:

• Creates a watertight seal at the water valve mounting interface to stop drips and seepage.
• Helps maintain correct valve alignment and prevents moisture from reaching nearby components.
• Addresses symptoms such as visible leaking at the valve, water on the cabinet floor, or moisture buildup near the valve area.
• Supports reliable water flow by preventing external leaks that can affect valve performance.

• One water valve absorption gasket

• Disconnect power and shut off water supply before servicing; relieve pressure in lines.
• Inspect mating surfaces and clean away debris or old gasket material before installing the new gasket.
• Replace only with the exact gasket specified for the valve to ensure a proper fit; hand-fit then tighten mounting fasteners to OEM guidance.

Washer won't start or stops mid-cycle? This power control board regulates electrical functions. Moderate DIY repair with basic tools needed.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Rod and spring assembly for washers. Installs in the suspension system. Replace if the rod is bent, spring is stretched, or assembly is broken or missing.

This lid hinge replaces a worn or damaged hinge on a top-load washer, restoring proper lid support and smooth opening/closing for safer, more reliable operation. Ideal when the lid sags, binds, or won't stay open. What it does:

• Provides pivot support so the washer lid opens and closes smoothly
• Restores correct lid alignment to prevent binding or uneven gaps
• Helps the lid stay in the open position during loading and maintenance
• Reduces stress on the lid and surrounding trim caused by a failing hinge

• Disconnect power before starting any repair and keep the lid supported while removing the old hinge
• Basic hand tools required; follow OEM service manual steps for hinge removal and attachment
• Inspect hinge mounting points and screws; replace any damaged fasteners
• Test lid operation after installation to ensure smooth movement and proper alignment

If your washer is leaking water or has low water pressure, this hose connector restores a secure seal and normal flow. Simple DIY fix in minutes.

Washer won't start or stops mid-cycle? A faulty lid switch prevents operation when the lid isn't securely closed. Simple DIY fix in under an hour.

Replaces a cracked, broken, or missing washer lid. Securely closes the tub opening to contain water and prevent splashing during wash cycles.

Washer won't fill properly or overfills? This water level pressure switch senses and signals correct fill levels, preventing overfill and underfill issues.

Replace your washer's damaged or worn hose. This essential component connects water lines and drainage systems. Order now if yours is cracked or leaking.

Washer not draining or making loud noises? This drain pump removes water from the tub during the drain cycle. Moderate DIY repair, typically takes 30-45 minutes.

Replace your worn washer drive belt to restore proper drum rotation and eliminate squealing or slipping. Confirm fit with your model number before ordering.

Connects the water inlet hose to your washer's fill valve. Replace this coupler if it's cracked, leaking, or damaged to restore a secure water connection.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.