Parts for Whirlpool WET4024HW0: Washer Top And Control Parts

The Lid Assembly is an OEM part for Whirlpool washers. It provides a protective barrier maintaining internal temperatures while allowing easy access.

Causes for replacement include cracked or depressed surfaces from years of use. Deterioration of seals from chemical exposure can also compromise intended leak resistance.

Symptoms relate to:

• Inability to securely lock lid in fully covered position
• Drafts sensed around perimeter when washing
• Warping reducing flush fit across washer enclosure
• Loosening from hinge pin attachments disrupting function

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This cover is an exact replacement access panel that protects internal components and restores the appliance's proper fit and finish. It helps keep wiring and parts enclosed for safe, reliable operation. What it does:

• Shields internal components and wiring from debris and accidental contact
• Restores the appliance's exterior appearance and proper alignment
• Secures openings to maintain safe operation
• Helps prevent moisture and dust intrusion into service areas

• One cover

• Disconnect power (and water, if applicable) before beginning any service
• Use basic hand tools; retain all fasteners during removal
• Handle edges carefully to avoid cuts; gloves recommended

This top panel is the replacement cabinet top that covers the appliance's upper section, protecting internal components and providing a finished surface. It restores the exterior appearance and support for the control area. What it does:

• Replaces a dented, rusted, or damaged top to restore a clean exterior
• Protects internal components and wiring located beneath the top
• Provides a stable surface around the control/console area
• Helps prevent moisture and debris from entering the cabinet

• Disconnect power (and gas if applicable) before beginning any repair
• Basic hand tools are typically required; some models may require removing the console or control panel
• Handle panel edges carefully to avoid cuts; have a helper for alignment on larger models
• Refer to your model's service manual or parts diagram for exact removal/installation steps

This replacement screw is a direct-fit fastener designed to secure appliance panels and components, restoring proper fit and reducing vibration or rattling caused by missing or loose hardware. What it does:

• Fastens panels, trim, brackets, or components to restore proper alignment
• Stops rattling or vibration caused by loose or missing screws
• Maintains structural fit where original hardware has been lost or damaged
• Matches OEM thread and head type for a secure, low-profile fit

• Disconnect power and water to the appliance before starting work
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; tighten until snug to prevent damage to threads or plastic parts
• If replacing multiple fasteners, use matching OEM screws to ensure even fit

The Pressure Switch is an OEM part for Whirlpool washing machines. It monitors pressure readings within the water and pump systems during wash cycles. The pressure switch maintains optimal water levels and flow rates by signaling pump operation based on real-time pressure feedback.

Causes of a bad pressure switch can include mineral buildup or corrosion, wear and tear over time, or damage due to impact or moisture damage. 

Symptoms of a bad pressure switch include:

• Incorrect or inconsistent water levels in the tub during fills 
• The pump failing to activate or stay running as needed
• Loud vibrating or knocking noises from inside the washing machine
• Suds or residual water left behind after cycles

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Valve is an OEM part for Whirlpool washing machines. It is responsible for regulating the flow of incoming water into the washer.

During cycles, the water valve opens and closes at timed intervals to admit the proper amounts of hot and cold water into the tub. It works in conjunction with other components like the water level sensor to fill the tub to the needed depth for each wash program.

Causes of a faulty valve can include mineral deposits clogging internal filters and sensors over time. Mechanical damage from rough handling may also impact performance.

Symptoms of a bad water valve include:

• Inability to select water temperature options
• Erratic or incomplete water filling of the tub
• Fluctuating water levels during cycles
• Persistent error codes related to water issues

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Board is an OEM part for Whirlpool washing machines. It is the "brain" of the washer, containing all the necessary electronic components and circuitry to operate cycles and run diagnostic routines. The control board receives input from sensors and directs power to motors, pumps, valves and other internal components through the wire harness.

Causes of a bad control board can include water or moisture damage, failure of electronic components over time due to normal wear, or damage due to electrical surges or power fluctuations.

Symptoms of a bad control board include:

• Washer not starting or running cycles correctly
• Error codes appearing on display
• Unresponsive or non-responsive buttons
• Inability to select cycles or options

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Latch is an OEM part for Whirlpool washing machines. This latch serves the important purpose of securely locking the washer lid in place during a cycle to prevent opening and potential safety hazards.

Causes of a bad latch can include worn or damaged locking mechanisms due to excessive use over time. It may also become faulty if exposed to impact.

Symptoms of a bad latch include:

• The washer lid not fully latching or locking in place
• Unstable or loose lid during operation
• Inability to start a cycle until properly latched
• Safety issues with potential for opening during operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness assembly connects electrical components to restore proper power and signal routing. Replacing a damaged harness helps stop intermittent operation and restores reliable control and sensor communication. What it does:

• Provides factory-style wiring connections between control, motor, and sensors
• Replaces frayed, burnt, or broken wires that can cause intermittent or no power
• Helps resolve symptoms like intermittent operation, failure to start, or control errors
• Ensures secure connector fit and correct wire routing for safe operation

• Disconnect power to the appliance before starting any repair
• Verify connectors match and engage fully; do not force mismatched plugs
• Route harness away from sharp edges and heat sources; secure with existing clips