White Westinghouse Refrigerator Parts

This upper hinge cover protects and conceals the refrigerator's door hinge assembly for a finished look and safer operation. It helps prevent snags and shields hinge components from dirt and wear while restoring the door's appearance. What it does:

• Covers the upper door hinge to hide hardware and improve aesthetics
• Helps keep dust, grease, and debris off the hinge area
• Reduces the chance of clothing or skin catching on exposed hardware
• Restores a finished, factory appearance when the original cover is cracked or missing

• High-level replacement; some models require removing or loosening the door or hinge fasteners
• Handle carefully to avoid scratching the finish; use the correct screwdriver or fastener tool
• Keep hands clear of the hinge while seating the cover and re-tightening fasteners

This replacement tank is the refrigerator water reservoir that holds and supplies water for the dispenser and ice maker, restoring normal filling and dispensing when the original tank is damaged or leaking. What it does

• Stores water supplied to the dispenser and ice maker so the system can fill as needed
• Prevents leaks and maintains proper water flow when intact
• Commonly replaced for visible cracks, leaks, or reduced dispenser flow
• Replaces a worn or damaged reservoir to stop pooling or water damage

• One replacement water tank

• Disconnect power and shut off the refrigerator water supply before starting
• Remove interior panels or shelving as needed to access the tank; keep track of fasteners
• Handle carefully to avoid cracking plastic or damaging nearby lines and fittings

A molded gasket that seals the evaporator coil cover to reduce air bypass and help direct cold air over the coils for more consistent cooling. Replaces a worn or damaged seal to help restore proper airflow and reduce frost buildup. What it does:

• Seals the evaporator coil cover to prevent warm air from bypassing the coil
• Helps maintain proper airflow for consistent cooling performance
• Reduces frost or ice buildup caused by air leaks around the coil cover
• Prevents condensation and dripping by keeping air where it belongs

• Disconnect power to the appliance before servicing to avoid electrical shock
• Thaw any frost/ice accumulation and remove the evaporator access cover per manufacturer instructions
• Clean mating surfaces, then press the seal into place ensuring a full, even fit around the cover

This replacement door seal creates a tight perimeter seal to help keep conditioned air inside and reduce moisture or frost buildup. Fits factory specifications to restore proper sealing and improve efficiency. What it does

• Forms an airtight barrier around the door to limit air exchange and energy loss
• Helps prevent frost, condensation, and water pooling inside or under the appliance
• Reduces strain on the compressor by maintaining correct internal temperature
• Common symptom fix for visible gaps, torn or flattened gasket, or excessive frost buildup

• Seal as shown

• Disconnect power or unplug the appliance before starting any service
• Clean the door frame thoroughly before installing to ensure a good seal
• Work the gasket into the channel evenly; avoid overstretching or twisting
• If clips or retainer strips are present, follow OEM guidance for proper seating

Left hand side. For the right hand side order 241674402

This is a replacement screw used to secure panels, trim and other appliance components to restore proper fit and reduce rattling. It matches the OEM part form and fastening function for compatible Frigidaire appliances. What it does:

• Secures panels, brackets or trim to maintain proper alignment and appearance
• Replaces missing, stripped or damaged screws that cause loose parts or vibration
• Helps prevent rattling and keeps components seated for safe operation
• Restores original fastening where a worn or corroded screw failed

• Disconnect power to the appliance before beginning any repair to avoid electrical hazard
• Use the correct screwdriver or driver bit and hand-start threads to avoid cross-threading
• Tighten until snug; avoid overtightening which can strip threads or damage panels
• If thread damage is present, replace with the correct OEM fastener (do not force)

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This compressor start relay helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. It replaces a failing start device to restore normal compressor startup behavior. What it does:

• Provides the initial boost to the compressor motor so it can start turning
• Commonly used when the compressor hums or won't start but power is present
• Can reduce repeated clicking or intermittent starts caused by a failed start device
• Works with the compressor's start circuit; does not replace sealed-system components

• One compressor start relay

• Disconnect power to the appliance before accessing electrical components
• Inspect associated start capacitor/overload if present; replace if faulty for reliable operation

This cantilever shelf clip secures a refrigerator cantilever shelf in place so shelves stay level and stable. It replaces a cracked or missing clip to restore proper shelf support and prevent shifting or slippage. What it does:

• Holds the cantilever shelf bracket/tier in the refrigerator liner to keep the shelf properly positioned
• Prevents shelf from tipping, sliding, or falling when items are placed on it
• Replaces worn, cracked, or broken clips that no longer grip the shelf brackets
• Works with standard cantilever-style shelving systems used in many refrigerators

• One cantilever shelf clip

• Remove food and glass shelves/trim as needed for safe access before replacing the clip
• Align clip with the shelf bracket slot and press firmly until it snaps into place; do not force beyond normal fit
• Handle glass shelves carefully to avoid breakage; wear gloves and eye protection if needed

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance