Richard G El Paso , TX December 18, 2018 Appliance: Model MAYTAG NEPTUNE The rollers needed to be replaced, the axles for the rollers needed to be replaced, the tension pulley roller needed to be replaced, the belt needed to be replaced It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Adjustable Wrench, Screwdrivers
David F El Paso , TX January 17, 2015 Appliance: Model MAYTAG, OLDER MODEL Girlfriend's dryer was making the dreaded "thumping" sound Ordered the parts on Sunday and they arrived on Tuesday with standard shipping. Went over today (Sunday), took the dryer apart and installed the new support wheels with new axles, washers and but. Reassembled the dryer, plugged it in and it sounded absolutely quiet. Whole job took about two hours, had to clean the interior while in there, and the girlfriend is very happy. Wonderful experience all the way around. Read More... 4 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Pliers, Screwdrivers, Socket Set, Wrench Set
Wayne V Franklin , WI February 09, 2015 Rear support rollers were shot drum was squeeking badly and eventually started knocking Looked up possible parts via a layout on the web site and ordered the parts I needed, plus a few extras. Figured I'm gonna open this thing once and be done with it. Once I got access to these rollers, via removing the drum from the front, it was an easy fix. The studs that support the rollers were locked so tightly they would not come out. Luckily these were still good and I just elected not to replace them. Dryer works like new! Read More... 4 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Pliers, Screwdrivers, Socket Set
Patrick C Muscoda , WI August 04, 2018 Appliance: Maytag Electric Dryer MDE5500AYW Dryer squeaked and started blowing fuse after running for awhile. Diassembled and replaced tumbler bearings, drum roller axles, drum support rollers, drive belt and cleaned all the lint out of dryer, blower and discharge duct. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 2+ hours Tools: Nut Drivers, Screwdrivers, Socket Set
Steven S Indio , CA April 26, 2016 Appliance: Maytag Gas Dryer MDG3000AWW Maytag neptune ten year old dryer making grinding and rubbing noises After watching your videos I decided to spend less than $200 and replace any parts that could be causing noises. It made sense to do this since I would have the dryer apart. I replaced the drum support rollers, the shafts, the belt tension pulley, all the fiber washers, the tumbler bearing kits and the dryer drum belt. After ordering the parts I noticed that a plastic piece for the lid and the drum front felt seal were also bad. I added those to the order with the aid of the sales staff. This also gave me the opportunity to vacuum up ten years of dust and lint inside that may have been a fire risk. I also found seals around the door had come loose so I re-glued them with your heat resistant adhesive. Your videos were invaluble. The step-by-step instructions made the job easy and I refered to them repeatedly before and during the repairs. Thanks to you I saved the cost of a new dryer or at the least the cost of an expensive repair service. I recommend you highly and won't hesitate to take advantage of your services again in the future if the need arises. Thanks. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Nut Drivers, Pliers, Screwdrivers, Wrench Set