Whirlpool WP65889-4 Run Capacitor OEM Part

Thank you to everyone who entered comments, especially about the "Clicking" sounds when it was trying to turn on the compressor. I did not notice them at first, but then heard them and was confident that one of these parts (or both) had a problem. In my case, I have custom cabinets around the sides of the refrigerator and hardwood floors in the kitchen so I put down some cardboard when the rollers would need to go at an angle due to a center island in the way. (I would rather do this myself rather than have a repair person rush it and kill my floors) Needless to say, it made more sense to replace both parts at the same time for me to do this repair the right way once to last another 8 years. The videos are great and gave me an idea where everything was. The only problem I had was a different (Modular) connector on my refrigerator where the 2 wires were right next to each other but the new part has the two wires separate and far apart from each other. They could not connect "as is". I had to run to radio shack, (luckily, the one by my house is not closing), buy the connectors ($4) , come back home, then cut my connector off and splice the wires separately. I called for support just to make certain where the blue wire went (On top) on the new part so I would not blow it out. Since this was an intermittent problem for me, i wanted to wait a full week to make certain the problem was solved. It has been running great for over a week now. After inspecting the old parts, the Overload Relay was burned up inside so I would say that was the defective part but I would still recommend replacing both since these attach to each other and there is really nothing else back there except the sealed compressor and a fan so replacing these parts before they fail makes sense when the unit is over 8 years old. They may also interact with each other and blow each other out since they connect together. Replace them both. Since the refrigerator started working intermittently after I reset it the first time, I ordered the parts slow boat. This site was so incredibly fast sending it out (FEDEX Ground) that it arrived the next day anyway. (This was incredibly appreciated since it died again the next day as the parts were arriving at the door) Extra Thanks to Appliance Parts Pros and FEDEX for the extremely fast service. I would give 5 out of 5 stars here but need to take off one for the following: A suggestion to the site is to make the radio shack connectors available on the site as an option when purchasing these parts (I would have opted to add the 4 dollars just in case I needed them since you don't know if you need them until you have opened up the back and there is probably a 50/50 chance you have the other style connector). Otherwise, keep up the great work with the videos and allowing us "DIY" folks to fix problems on our own. Excellent Site.

I Googled the model and looked up a troubleshooting chart. I went to the Appliance Pros website and found the parts I needed and ordered them. I watched the 3 minute repair video and when the parts came in I replaced them. The fridge runs colder and quieter than it ever has before. I'm not a very handy guy but have done many home repairs in the past year by viewing the videos on this website. This repair was very quick and easy. Two minutes!

I wrote down where the wire were plugged in. Pulled capacitor and overload relay. Ordered and replaced them and she's good as new.

The lights and fans worked. But since the compressor did not start, the fridge and freezer would not get cold. After removing the back access panel, I found a dead mouse and its nest beside the compressor. I pulled the run capacitor and start relay/overload switch from the compressor. The start relay/ overload switch is a solid state circuit. So, troubleshooting it is difficult. It did make a little rattle noise when shaked which can mean that it is bad. I measured 115 volts from the wires that plug into the start relay. The resistance between the 3 compressor pins showed continuity with respect to each other. None of the pins were grounded. The compressor body showed good ground. So, that all seemed to check out and point the issue to the run capacitor and start/ relay overload. The capacitor did show some resistance for a second which pointed the problem to the start relay/ overload. I decided to order both parts. They arrived a few days later and were OEM parts that fit exactly. After installing them, I plugged in the fridge and had the same buzzing noise at the compressor. It would not start. I shook it and gave it a few whacks with my hand and it finally started. The compressor struggled but then came up to speed. It's been operating for a few days now and is on its second bucket of making ice. The compressor is running quiet and the fridge and freezer are cold. The real test will be if the compressor starts up after a power outage.

I spent some time looking at the back of the compressor by the relay and saw that it had burn marks and one of the wires had burned off. I logged on the AppliancePartsPros.com and looked up the parts and looked for others that had similar problems. I had a version 10 which was about 15 years old. I did find some info enough to order parts, the difficult part of the process is that Overload relay on my compressor was a single part and the replacement was 3 different parts. The parts arrived and I got no instructions as how to convert to the new parts so I logged back on an found a very helpful video that was close enough to my compressor that I could do the replacement. It is important to note that wire colors are not consistent so paying close attention to where the wires are connected is important. After some work I was able to get everything hooked up and the Freezer and Refrigirator are working normally. I should note that I also changed the Run Capacitor also. Not sure it needed it however I would suggest doing it with this version of compressor.