Wizard Lawn Mower Parts

This replacement part is a hex screw. It is a genuine replacement part made by MTD. This type of part is very common in different types of appliances and machines. Hex screws are important in holding parts together so that the user is able to operate the appliance smoothly.A new hex screw might be needed if the user notices that different parts of the appliances are loose or missing. It is possible for hex screws to become stripped over time and will need to be replaced. The repair for this screw should be simple and will most likely require a screwdriver and perhaps pliers if the previous screw is stuck in place. This is a genuine OEM replacement part. This part is sold individually. It is sourced directly from the manufacturer to ensure proper fit and long-lasting use.

This discharge chute is a genuine MTD part, sold individually. This discharge chute can be used as a replacement part for a snowblower. This discharge chute provides a channel for the passage of snow that has been cleared out of the way by the snowblower so that the snow does not pack up tightly or blow in the face of the operator. The discharge chute of a snowblower might have to be replaced if it is not properly collecting and discharging snow or if the snow is packed too tightly to discharge properly. This could occur if the discharge chute has undergone too much scraping, scratching, or collision with the hard surfaces upon which it might be dragging. If this is the case, the discharge chute should be removed and replaced with this genuine OEM replacement part. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This discharge chute is compatible with the following outdoor appliance brands: MTD and Craftsman.

This is a height adjuster knob for walk-behind lawn mowers. It attaches to the height adjuster lever. This component is used to adjust the front wheels on the lawnmower deck. This adjustment allows the user to select the desired cutting height of the grass. This component is made out of a hardened foam material that is easy to grip.If the height adjuster knob falls off of the height adjust lever and will not reattach, it is likely that it will need to be replaced. The height adjuster lever itself is sold separately. The repair person may wish to wear gloves when replacing this part.This component is sourced straight from the manufacturer. It is sold individually and is a genuine OEM part. This height adjuster knob is compatible with walk-behind lawnmowers that are manufactured by the Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, Craftsman, and Husky brands.

This is a replacement spacer for walk-behind lawn mowers, riding lawn tractors, snowblowers, and other outdoor machinery. The spacer prevents parts from grinding together and wearing down. This spacer fits over the axle areas and is a small, flat, metal ring.Over time and through wear and tear, a spacer can go bad or get bent. This is also dependent on frequency of use. For equipment used maybe once a week (or month, depending on the season), replacing a spacer may never be a concern. For machines used more frequently, it may be a rather minor fix. Replacing the spacer is simple, and requires a screwdriver, pliers, wrench, and a pair of durable gloves. The replacement requires some disassembly of the lawn mower and its inner workings.This is a genuine OEM replacement spacer. This part is compatible with over 150 products and machines. This part is sold separately.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

The wheels of a lawnmower and other lawn care equipment take a lot of abuse, even on well cared for machines. They can wear down over time, making it difficult to maneuver the equipment. Eventually, it may be necessary to replace the wheels if they are no longer rolling properly or if they have cracked. This wheel is eight inches in diameter and is easy to replace in just a few minutes. This OEM replacement wheel is sold individually and is compatible with many different types of lawn and garden equipment. These include lawnmowers, snowblowers, tillers, edgers, and log splitters. The wheels work with a range of brands, including Craftsman, Mastercut, Montgomery Wards, Sears, Bolens, MTD, Yard Machines, and Cub Cadet. Keep in mind that this is an individual wheel, so be sure to get as many as needed for the equipment.

The blade support is found between the blade and the bolt. As its name suggests, it is designed to provide support for the blade to ensure it is secured to the base of the mower deck. It is made of metal and it will need a replacement if it becomes worn or damaged. To replace a blade support or blade spacer, first, the engine needs to be cool. Remove the wire and boot from the spark plug. Tip the mower back on its handle assembly and use a piece of wood or sturdy object to hold the cutting blade in place. Remove the old blade support and blade. When installing the new one, ensure that the blade's sharp edge faces away from the mower deck. Re-thread and torque the bolt between 40 and 50 ft-lbs. This is an original OEM replacement part for lawnmower blade support made by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, MasterCut. It is sold individually.

This screw is a hex wash head screw. It is a genuine MTD part. It is a replacement part for various makes and models of lawn mowers, snowblowers, edgers, and other equipment. A screw is a type of fastener, and as such, there are many screws on these appliances.Screws may become worn over time through normal wear and tear. In addition, screws can become stripped when making another repair, so it is a good idea to have compatible screws on hand in case. This hex wash head screw is made of durable metal.This screw is a genuine OEM part that is sourced directly from the manufacturer. It is sold individually, though there are many screws located on these types of equipment. It is made to be compatible with equipment manufactured by MTD, Yard Machines, Bolen, Troy-Bilt, Craftsman, Husky, Cub Cadet, and many others.