Wizard Tiller Parts

This dowel pin is a genuine MTD part, sold individually. This dowel pin can be used as a replacement part for a lawn mower, a tiller, or a wood chipper. The purpose of a dowel pin in one of these tools is to serve as a fastening component that affixes two different components to one another by fitting into the cylindrical hole of the dowel pin.The dowel pin can be easily lost or misplaced as it is a small component. The dowel pin can also become stripped. If this occurs, the component should be immediately replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. The operator of the appliance should be aware that this component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This dowel pin is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, MasterCut, and Yard Man.

This tap hex screw is a genuine MTD part, sold individually. A tap hex screw can be used as a replacement part for outdoor appliances including lawn mowers, tillers, and edgers. This is a small fastener.The tap hex screw for one of these outdoor appliances might be subject to damage or to a loss or misplacement that can necessitate the full replacement of the screw. Refer to the manual for detailed instructions.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This tap hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard Man, Turf King, and MasterCut.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This replacement part is an extension spring and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This extension spring is found in different types of lawn mowers and helps other parts to work together and allow the engine to run properly and smoothly.A new extension spring might be needed if the current one is damaged or missing from the appliance. Because of the nature of the extension spring, it is not unusual for it to become stripped or snapped due to normal wear and tear within the machine. Unusual sounds may come from inside the machine if this spring is not working properly. This is a genuine OEM replacement part and is sold individually. This spring is sourced directly from the manufacturer to ensure proper fit.

This replacement part is a washer. This is a genuine replacement part made by MTD. A washer is a small part but important to the overall workings of the machine. Washers work with other small pieces such as nuts and screws to keep parts in place and in proper working order.A new washer might be needed if the current one is missing or damaged in any way. This can be caused by normal wear and tear. Washers may experience a large amount of friction over time and can become stripped down after a while. If this is the case, be sure the replace the part as it might not be as effective as during prior uses. This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.

This part is a replacement shaft. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective shaft in a variety of tiller models.The shaft is critical to proper tiller function but can become damaged, dented, bent, or otherwise rendered ineffective, particularly with regular equipment use on rough terrain. Thus, the shaft will need to be replace for the tiller to function as intended. It's important when working on or near to an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this shaft, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this shaft is suitable for use on several different models of tillers manufactured by MTD, Craftsman, and other brands. Please This is a genuine part made of high-quality, durable materials and is sold individually.

This replacement part is a tiller flap intended for use on lawn mowers. It protects the user and equipment from flying debris that might cause harm during use.A new tiller flap might be needed if the current one is missing or damaged at all. This can include the part being torn, bent, or cracked in any way. This part can be damaged after years of normal wear and tear and should be replaced if this is the case. Be sure the engine is powered off before attempting to replace or repair this part. This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.