Yard Machines Chipper Shredder Parts

This is a valve cover gasket that is used in a number of small gasoline engines for a variety of lawn, landscaping, and outdoor power tools including log splitters, chippers, leaf blowers, power vacuums, tillers, and snow blowers. The valve cover gasket provides a seal between the engine's cylinder head and the camshaft to prevent oil leaks. The gasket also seals the spark plug port. This seal prevents the engine oil from entering the combustion chamber. Over time, these gaskets are subjected to heat extremes and the constant vibration of the small engine that runs at about 3,600 revolutions per minute. It is not uncommon for a valve cover gasket to begin to leak after several years of service. The first sign of this is usually white smoke emitted from the engine's exhaust, which is a sign of oil burning in the fuel mix. Eventually, the engine will lose power, as well. When replacing this part, make sure to use a gasket such as this one, which is a genuine OEM replacement part, manufactured to be identical to the specifications of the original gasket. This gasket is compatible with small engines made by Bolens, Huskee, MTD, Troy-Bilt, Yard Man, and Cub Cadet.

The carburetor is responsible for combining fuel and air within the engine to make internal combustion happen. A carburetor gasket acts as a boundary between where the air is and isn’t meant to be within an engine. If the carburetor gasket is blown, the air to fuel ratio will be off, and the motor will not combust properly. A bad gasket will cause the motor to stall out at idle or vibrate badly. The throttle will not behave properly either. Using a screwdriver, install this genuine OEM part by taking apart the carburetor, removing the old gasket, and putting the new one in place. Be sure to clean all the parts when taking apart the carburetor. This part is sourced directly from the manufacturer, and it is shipped individually. It is compatible with Craftsman, Cub Cadet, MTD, Huskee, and many more brands of snowblowers, lawnmowers, tillers, chainsaws, chippers, and many other tools with small motors.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The function of a carburetor insulator in a small engine appliance is to maintain a lower temperature for a running engine and to keep that heat away from the carburetor, the purpose of which is to mix the air and fuel in order to start the engine. A functioning carburetor insulator will prevent the engine from overheating.A broken or non-functioning carburetor insulator will likely not prevent the engine from operating, but it might slow down its power or reduce its fuel economy due to compensation from overheating. An engine with a damaged carburetor insulator might take in more fuel than usual or allow in unmetered air. An unmetered air leak can cause damage to the engine in the short-term so if there appears to be visible damage to the carburetor insulator, it should be replaced as soon as possible.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.

This is a cylinder head gasket that is an OEM replacement part sourced directly from the manufacturer for use on lawn mowers and other small engines in outdoor lawn and garden equipment. The head gasket is the engine block that separates the cylinder head from the engine block. This gasket is used to prevent oil from mixing with coolant. The cylinder gasket seal also seals the internal combustion process, putting it under the pressure it needs to operate. If the gasket is worn or cracked and the pressure is not right, the engine will not operate correctly, and there will be a loss of power. Oil leaks are another way to tell that the cylinder head gasket is bad and needs to be replaced. Before deciding if the cylinder head gasket is the problem, a compression test should be run using a compression gauge. After pulling the starter cord, the internal pressure should read 60 psi. If the reading is less than this, the cylinder head has lost compression, and the gasket should be removed and replaced. This cylinder head gasket is sold individually. This gasket is designed for use on lawn mowers and small engines manufactured by MTD, Yard Machines, Troy-Bilt, Yard-Man, Cub Cadet, and Husky.

This is a high-quality connecting rod assembly that is used in many types of lawn and garden equipment from several manufacturers. It has a metal rod that connects to the crankshaft and piston. The purpose of the connecting rod is to allow pressure and combustion to rotate the engine's output. If this part is damaged or broken, the garden equipment may not work or may not have the desired level of performance. If this happens, the connecting rod assembly should be replaced.A basic set of tools and work gloves will be needed to replace the connecting rod assembly. First, turn off the tool with the damaged rod and put it on a level and sturdy surface. The spark plug wire should be disconnected to prevent the engine from turning on. Access the rod and replace it with the new part before use.The connecting rod assembly is sold as an individual part. It is an authentic OEM replacement component that is sourced directly from the manufacturer. The part is made to be compatible with lawnmowers, wood chippers, snowblowers, log splitters, tillers, and leaf blowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Huskee, Troy-Bilt, MTD, and Yard Machines.

This governor spring is a genuine MTD part, sold individually. This governor spring can be used as a replacement part in lawn mowers, tillers, leaf blowers, log splitters, and wood chippers. The purpose of a governor spring for these outdoor appliances is to facilitate the opening and closing of the throttle which helps the appliance maintain its even pace and speed while in operation.The governor spring in an outdoor appliance might have to be replaced if it loses its spring tension. This could occur as the result of a collision with a hard object or due to general wear and tear over long-term use. If this damage prevents the governor spring from serving its typical function, it should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This governor spring is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Craftsman, Troy-Bilt, Yard Machines, Huskee, Yard Man, and MasterCut.

It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, there may be a problem with the carburetor. It could be a leak that causes compression problems keeping the machine's engine from starting. Gasoline may drip from the float bowl because of an O-ring that won't seal or seat evenly all around, or one that has become brittle over time. This is a genuine OEM part compatible with specific lawnmowers, snowblowers, wood chippers, log splitters, tillers, and other garden maintenance machines from Craftsman, MTD, Cub Cadet, MasterCut, Troy-Bilt, and Yard Machines. It is sold individually.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This is an oil dipstick assembly that is a crucial part of many types of lawn and garden equipment. The dipstick is made of quality plastic and metal and is located inside the oil fill tube. The purpose of the part is to indicate how much oil is currently in the engine. Regular use can cause this component to wear out or become damaged over time. When this occurs, it's not possible to determine how much oil is present so the oil dipstick assembly will need to be replaced.Replacing the oil dipstick assembly is a simple and quick process. No tools are needed to make the replacement. Turn off the equipment and access the oil fill tube. Unscrew and remove the old oil dipstick tube before replacing it with the new component. The equipment can then be used as normal.This oil dipstick assembly is a genuine OEM replacement part that is directly sourced from the manufacturer. The part is sold on an individual basis. This component is made for use with lawnmowers, snowblowers, tillers, leaf blowers, log splitters, and wood chippers created by MasterCut, Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

This carbon canister is a device used to control the amount of gas pollution that is released from small engines found in various lawn and garden machines. This is a genuine OEM replacement part that is sourced from the manufacturer. It is an emission control device also known as a charcoal canister. As gas evaporates from the fuel tank, the carbon canister catches the fumes and releases them into the engine so that they are not dispersed into the atmosphere. Age and regular use may cause the canister to crack or break and not hold the fumes inside. Typical signs that the canister needs replaced include strong fuel odors or leaking from the canister. If the canister is flooded by fuel, the canister will not operate properly. Fuel will spill out, and the canister will need to be replaced. Before replacing the carbon canister, empty the fuel from the machine and remove the spark plug wire for added safety. This repair should be made in a well-ventilated area.The carbon canister is made from heavy-duty plastic and is sold as an individual unit. It is compatible with tillers, chippers, and other small engines manufactured by MTD, Cub Cadet, Yard Machines, and Troy-Bilt.

This silencer plate is used on a variety of outdoor lawn and garden machines to reduce the noise from the air intake. This molded plastic part sits on top of the carburetor and houses the air filter. It provides an added layer of noise muffling. Exposure to wind, rain, and heat can cause the plastic to become brittle and cracked. The silence plate should be replaced if damage is discovered during routine maintenance. A screwdriver is needed to replace the silence plate. Before working on the machine, make sure the engine is cool and remove the spark plug. Remove the air filter cover and the air filter to access the silencer plate. Remove the screws holding the plate in place. Install the new silencer plate. Tighten the screws. Install the air filter and housing cover. This silencer plate is made of durable molded plastic and is sold individually. It is a genuine OEM replacement part sourced directly from the manufacturer. This part is compatible with tillers, chippers, shredders, and small engines manufactured by Cub Cadet, MTD, and Yard Machines.

This replacement part is a roll over valve. This is a genuine replacement part made by MTD. This part is found in many machines and is primarily a safety device that ensures that the fuel tank does not leak in the event of a vehicle roll-over. A new roll over valve might be needed if the current one is missing or damaged in any way. If the fuel tank is leaking when on it's side or upside down, it might be due to this part not working properly. If this is the case, be sure to replace it as soon as possible. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a starter recoil assembly. It is used when starting small lawn equipment and other machines. It engages the flywheel. With time and use, any or all of the recoil can wear out or become damaged, including the spring, housing, rope, or pulley. If something is damaged or worn out, the entire starter recoil assembly must be replaced. Signs that the part requires a repair include an engine that won't start or has difficulty engaging.Replacing a starter recoil assembly is easy and can be done in about 15 minutes. A nut driver and screwdriver are required for the repair. Wear gloves. Make sure the equipment is completely cooled before beginning the recoil assembly replacement. After putting tension on the spring and pulley, hold the housing securely to prevent it from releasing.The starter recoil assembly is a genuine OEM-authorized replacement part. It is sold individually. The starter recoil assembly is compatible with MTD, Cub Cadet, Yard Machines, Husky, Yard-Man, and Troy-Bilt brands. It is a complete part that includes the housing, rope, pulley, and recoil spring. It works with small engines, lawnmowers, log splitters, trimmers, and other similar equipment.

This replacement part is a shredder bag assembly intended for use on lawn mowers. This part is able to catch grass clippings, mulch, and other debris during use. The bag attaches to the back of the mower and ensures that the debris is caught. A new shredder bag assembly might be needed if the current one is missing or is unable to hold the debris during use. Damage can include tears in the material, holes allowing debris to escape, or rips along the seams. Be sure the engine is powered down before attempting to replace this part. This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This vacuum impeller is a genuine MTD part, sold individually. This vacuum impeller can be used as a replacement part in a lawn mower or a wood chipper. The purpose of a vacuum impeller in a lawn mower or a wood chipper is to spin at a high enough speed to generate air flow so that the vacuum of the appliance can draw in or push out pressurized air, a crucial feature of both a lawn mower and a wood chipper.The vacuum impeller in a lawn mower or a wood chipper might need to be replaced if the vacuum impeller suffers too much damage to serve its typical function. If the vacuum impeller cannot rotate at a high enough speed due to reduced functionality or cannot spin at all due to potential damage to the component, the vacuum impeller should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This vacuum impeller is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, and Yard Machines.