Yard Machines Snow Removal Equipment Parts

The hex screw is a specialty screw that has various uses on lawn and garden equipment engines and housings. Over time, screws are known to become worn, corroded, lost, or otherwise damaged. This is an identical replacement that will have many locations and applications, but when it becomes damaged or gets lost it should be replaced as soon as possible. This is a specialty screw that is not designed for general use. Refer to parts diagrams for the appropriate location and installation of this screw for a guaranteed fit. This OEM hex screw is manufactured to exact standards and can be used in more than 150 different brands of machines. It is compatible with snow throwers, lawn mowers, and blowers from RYOBI, Yard Machines, Yard Man, Poulan, Troy-Bilt, MTD, Bolens, Cub Cadet, and Husky. This high-quality hex screw is made of metal and sold as an individual unit. Those who need more than one screw will have to purchase multiple quantities. A wrench is required to replace this screw. Always allow engines to cool completely before performing any repairs and wear gloves for hand protection.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This replacement rubber paddle kit that is used for snowblowers and snow throwers has been sourced from the original manufacturer. The paddles connect to the auger bracket. They are responsible for moving the ice and snow through the chute assembly. If there is a problem with the paddles, the machine will not be capable of moving the snow effectively. The rubber paddles are exposed to the elements when using the machine. They could become damaged by any number of things. They might be broken or cracked during use, or they could wear out and start to break down over time. The screws that hold them in place could corrode or become damaged, as well. When there are issues with the paddles, owners should replace them all at the same time. With this genuine OEM rubber paddle kit, buyers will receive two paddles, as well as the hardware needed to add them to the machine. The paddles are compatible with many models of snowblower from Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, and Yard-Man.

This part is a speed select cable. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or detached speed select cable on certain snowblower models. The speed select cable works by fastening the ground drive system to the speed control level. This enables the equipment operator to properly control speed and traction while using a snowblower. Over time, speed select cables can experience wear and tear which can cause them to break or become detached, requiring replacement. Without a functioning speed select cable, the snow blower will not be able to be properly controlled. For accurate information on how and where to install this replacement speed select cable, specific manufacturer diagrams should be referenced. Proper safety measures should always be followed when working on any type of equipment.As an authentic replacement part, this speed select cable can be used on multiple different models of Craftsman, MTD, Yard-Man, and Huskee snow blowers. Please note that this speed select cable is a genuine part made of high-quality materials and is sold individually.

The auger belt is a rubber v-belt that goes around the auger on two-stage snow throwers. The belt is responsible for helping ensure smooth rotation of the auger. Since it is made from rubber, it can wear out over time and snap off or become so damaged that it doesn’t work effectively. Replacement of the belt is a part of routine maintenance that comes with snowblower ownership. The belt can be replaced in no time using a basic wrench set. This auger belt is compatible with several snow throwers, including models from MTD, Cub Cadet, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It works with hundreds of different machines and is made from a durable rubber material.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

The shave plate, also called the scraper bar, is an important but often overlooked part of a snowblower. This thin metal strip sits at the bottom of the auger housing against the ground and gathers the snow the auger will expel through the chute. Made of hard plastic, the shave plate is the only part of the snowblower that actually touches the snow-covered ground without rolling. As durable as the shave plate is manufactured to be, it constantly comes into contact with unseen objects that pound, slice, and pit it. Eventually, the shave blade has to be replaced. To replace the blade, simply invert the blower, unscrew the old blade, attach the new blade, and put the blower right side up again. As long as the user is replacing the shave plate and has the machine upside down, this is an ideal time to check for damage to the wheels, the auger blades, driveshaft, and the condition of the shear pin. If this replacement is taking place in preparation for the coming winter, it might be a good time to replace the oil and oil filter as well. Be sure to use genuine OEM replacement parts that perfectly match the factory originals. This blade is compatible with snowblowers made by Yard-Man, Bolens, Yard Machines, Troy-Bilt, Craftsman, Ryobi, Cub Cadet, Huskee, Montgomery Wards, and Ryobi.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

In a snowblower, the driveshaft is connected to a part called a worm gear. The worm gear turns the auger blades which eject the snow. The worm gear is connected to the worm shaft, which causes the auger blade to turn rapidly. Eventually, the incredible torque inside the machine, plus the occasional bumps and bruises experienced by the machine in operation and when being stowed, may cause the worm gear to malfunction. When the snowblower is erratic in its operation and fails to remove snow completely, there is a good chance the problem is the worm gear. To replace the worm gear, remove the housing to get to the worm shaft. Remove the entire worm assembly. Next, remove the blower fan and remove the worm gear. Grease the auger assembly before installing the new gear. Reverse the order to reassemble. While the snowblower is disassembled, it's the best time so exam the auger, driveshaft, sheer bolts, and tires for wear. You may find other parts that need to be updated. Make sure to replace the worm bolt and any other necessary parts with a genuine OEM manufactured part such as this one. This gear can be used in a number of snowblowers, including machines made by Yard Machines, Craftsman, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, Ryobi, Montgomery Wards, Huskee, and MTD. Part sold individually.

This drive cable is made up of a metal cable housed by a flexible plastic casing. It connects the drive control in the handle of the snowblower engine. This ensures the equipment starts and stops when a person wants it to. If the cable is damaged or broken, the snowblower will not work properly even when the control handle has been released.If the equipment isn't stopping or doesn't start when it should, the drive cable could be causing the problem. It will need to be replaced for the snowblower to work properly. Before making the replacement, the spark plug wire should be removed. Next, release the cables in the handle. The drive cover should be removed before taking out the drive cable. Replace this with a new drive cable and reassemble the snowblower before using it.This is a genuine OEM replacement drive cable that is sourced directly from the manufacturer. It is sold as an individual part. These cables are made to fit snowblowers created by MTD, Craftsman, and Yard Machines.

The snowblower auger driver belt is made from high-quality rubber and has a special design that features cogs. The belt is what will rotate the augers in the snowblower. Belts in snowblowers and other types of equipment tend to wear down over time and use. The belt might begin to stretch and no longer be able to rotate the augers. It could also crack or break. If any of these things happen to the belt, it would require a replacement before the machine could be used again. The belt is relatively easy to replace when the time comes. The genuine OEM snowblower auger driver belt is sold individually. It can be used with a number of models of snowblowers from Craftsman, Yard Machines, MTD, Huskee, and Cub Cadet. Whenever buying a new belt or any replacement parts, owners should always check to see that they are buying the correct option for their make and model.

This is a shear bolt, also known as a shear pin, which is used in many models of snowblowers. The shear bolt connects the auger shaft to the auger on the tool. This connection allows the augers to rotate, collecting snow and sending it to the impeller fan. Most snowblowers have at least one shear pin on each side of the auger gearcase. Large objects that get stuck between the housing and augers can damage the pins, necessitating replacement.If there is damage to the shear bolt or if it has broken, the snowblower may not work as expected. To replace the bolt, the snowblower should be turned off. Wear work gloves and remove the spark plug wire before disassembling the snowblower to reach the shear bolt. It can be removed and replaced with a new part.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The shear bolt is designed for use with snowblowers created by Yard-Man, Yard Machines, MTD, Montgomery Wards, and Huskee.

The torsion spring is designed to create tension between various components in lawn and garden equipment engines. This spring may have multiple applications depending on the type of machine. The torsion spring typically connects levers and other things that need pressure to operate properly. They create torque and help support various items in lawn and garden machines. Over time, they can become worn or the springs can stretch or snap. This will require a replacement of the entire spring, since the unit will typically not be able to function without a properly working torsion spring. This genuine OEM replacement spring is manufactured to exact standards by MTD. This part can be found in hundreds of models from MTD, Yard Machines, Cub Cadet, Troy-Bilt, Husky, Bolens, and Yard-Man. Check the parts diagrams and equipment manual for the exact location and application of this torsion spring. This high-quality spring is made of metal and is sold as an individual unit. Always wear gloves when performing repairs on lawn and garden machines. Beware of pinching and crushing injuries when working with springs, which are typically under a lot of pressure.