Yard Machines Snow Removal Equipment Parts

This spacer is a genuine MTD part, sold individually. This spacer can be used as a replacement part in lawnmowers, snowblowers, and wood chippers. This part assists in fastening two components together by creating a slight gap that reduces friction.The spacer might have to be replaced if it is lost, misplaced, or damaged from general wear and tear with long-term use. If the spacer is lost at some point within the typical operation of the appliance and its absence is noticed by the operator, the spacer should be replaced by this genuine OEM replacement part. If the spacer is damaged beyond functionality, the spacer should be immediately replaced. This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This spacer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Huskee, Yard Machines, Montgomery Wards, Yard-Man, Turf King, and MasterCut.

This replacement part is an upper handle intended for use in lawn mowers. This is a genuine replacement part made by MTD. Handles are a very important part to walk behind lawn mowers and are essential in helping the user guide the machine in the correct direction. A new upper handle might be needed if the current one is broken or damaged in any way, including being dented, bent, or cracked. It is common that this part will need to be replaced after years of normal wear and tear. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. It is recommended that the user refer to the appliance manual for more detailed instructions on how to install this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn mowers made by MTD.

This belt is used for snowblowers. When the machine is running, the belt turns and propels the auger, which then blows the snow through the chute. If the belt is broken or otherwise not functioning properly, the snowblower will not work.The belt may need to be replaced for any number of reasons. It could become damaged while in use, although this is rare. Over time, the belt could start to stretch and weaken. It may not longer provide the same level of efficiency as when it was new. There is also the chance that the belt could snap. When replacing the belt, it is recommended that the owner also clean the pulleys. This can prevent premature wear and tear.This snowblower belt is for use with many models from MTD, Yard Machines, Cub Cadet, and Troy-Bilt. The belt is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This replacement part is an auger pulley, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This auger pulley is generally found in snowblowers and is an important part of the appliance. The auger pulley causes a rotating motion and helps the engine expel the air used to blow snow. A new auger pulley might be needed if the user notices that the auger is no longer rotating properly or is slower than before. It is common for this part to be replaced after a while of normal use as the pulley and auger can both become stripped due to friction overtime. Be sure to wear work gloves while replacing this part.This auger pulley is sold individually. This part is also genuine OEM replacement part sourced directly from the manufacturer. Be sure to refer to the specific owner's manual for more detailed instructions on how to replace this auger pulley.

This part is a replacement auger pulley. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective auger pulley in snow blowers.The auger pulley rotates the snow blower's auger blades by connecting the auger gearbox to the equipment's drive belt. This part is critical for proper functionality and thus will require replacement if faulty. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this auger pulley, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This auger pulley can be used with different models of snow blowers that have been manufactured by MTD, Craftsman, Ryobi, and other brands. Part sold individually.

Slide shoes, otherwise known as skid shoes, are attached to a snowblower to help protect the concrete it moves over. The slide shoe also helps to protect the underside of the snowblower. They are composed of metal and are attached to the bottom of the machine. With use, the slide shoes may wear down. They can also become defective from accidents while operating the snow throwing machine. When the slide shoes are not working correctly, there can be irreversible damage done to both the snowblower and the concrete. Replacement slide shoes can easily be attached to the bottom of a snowblower. Be sure to allow the machine to cool down completely. It's recommended to set the snowblower on top of a piece of cardboard. Remove the old shoes and install the new ones, tightening all nuts and washers while the skid shoe is flat on the ground.This is a manufacturer supplied OEM MTD snowblower slide shoe. Each shoe is sold separately. The slide shoe is made of high-quality, durable black steel. It is suggested to replace both shoes simultaneously to ensure an even and consistent path for the MTD snowblower.

This shave plate is a genuine OEM part sourced directly from the manufacturer for use on snowblowers. The shave plate collects the snow and pulls it into the auger, where paddles then throw the snow away from the path being cleared. If the shave plate is damaged due to normal wear and tear, the snow plate will leave behind snow. Snow plate inspection should be part of the first inspection of the season. Make sure the snowblower is cool, and jack it up on a ramp to get underneath for easier access to the shave plate. Remove the spark plug and key from the snowblower. Wear safety gloves and safety goggles when working on the machine. Locate the shave plate underneath the blower. Loosen the bolts and take the shave plate off. Install the new shave plate and install the bolts from the original shave plate. Reinstall the spark plug and test the machine. If the plate needs to be lowered, repeat the process but don't remove the plate, just lower it slightly.This shave plate is a black metal part that is sold individually. It does not come attaching hardware. It is designed for use in snowblowers manufactured by Yard Machines, MTD, Troy-Bilt, Husky, Yard-Man, and MTD.

This part is a shave plate. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a damaged, detached, or worn shave plate on certain models of snowblower. When using a snowblower, stubborn or stuck pieces of snow can affect proper functionality. Shave plates attach to the underside of the snowblower to help scoop stubborn snow or slush into the auger housing. Over time, as they regularly scrape the ground, shave plates will become worn and will no longer make sufficient contact with the pavement. In order to ensure snow blowers continue to do their job efficiently, shave plates should be replaced once they exhibit signs of deterioration. Proper tools are needed to replace this part and appropriate safety guideline should always be adhered to.As an authentic replacement part, this shave plate can be used on multiple different models of snow blowers manufactured by Cub Cadet, Craftsman, Huskee, Troy-Bilt, Yard-Man, and MTD. Please note that this shave plate is a genuine part made of high-quality, durable materials and is sold individually.

This part is a replacement drive belt. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace broken, snapped, or defective drive belts in a variety of snow blower models. The drive belt is what helps to power the snow blower and is critical to proper equipment functionality. Belts are subject to significant amounts of wear and tear and must be replaced if snapped, worn, brittle, or otherwise rendered ineffective. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this drive belt, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this drive belt is suitable for use on several different models of snow blowers manufactured by MTD, Craftsman, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This replacement screw is useful for many different types of handheld outdoor equipment. Screws are used as a means to hold parts of the machine together. The screws also help to reduce the amount of vibration that occurs in the machine.These screws are used in outdoor equipment, so there is a chance they could corrode over time. In some cases, the screws may also lose their thread, or the heads of the screws could start to become worn down. Owners who notice issues with the screws, or who notice a missing screw should replace them to ensure the proper function of the machine. Failure to replace damaged screws could result in more difficulty replacing them after they wear down further.The screw works on various types of equipment including blowers and trimmers. It is compatible with a range of brands including Murray, Craftsman, Yard Machines, Bolens, Yard-Man, Craftsman, Ryobi, and McCulloch. This is a genuine OEM part sourced from the manufacturer, and it is sold individually.