Yard-Man Lawn Mower Parts

This part is a replacement sphere bearing assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a worn out, damaged, or defective sphere bearing in a variety of outdoor power equipment.Sphere bearings have a variety of uses. They are particularly useful for equipment with a high load capacity that also requires high tolerance and self-aligning ability. They can be found in a wheel assembly, transmissions, or other machinery parts. Sphere bearings are subject to significant wear and tear, requiring replacement. When working on or near to an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this sphere bearing assembly, the appropriate owner's manual and equipment diagrams should be referenced. As an authentic replacement part, this sphere bearing assembly is suitable for use on several different models of small engine outdoor power equipment manufactured by MTD, Yard Machines, Cub Cadet, Yard Man, Bolens, and Troy-Bilt. This is a genuine part made of high-quality, durable materials and is sold individually.

This carburetor gasket is located between the insulator and the carburetor, creating a strong seal between the two to allow for optimal compression and engine performance. Over time and due to constant heat exposure, gaskets can degrade or become damaged. This can result in leaks in the system, which will impact performance and could cause the engine to fail completely if not properly addressed. If the carburetor gasket becomes faulty in any capacity, it needs to be replaced as soon as possible. This genuine OEM gasket replacement is manufactured to exact standards and is compatible with several models of snowblower engines from Troy-Bilt, MTD, Yard Man, Yard Machines, Cub Cadet, and Husky. This gasket is made of durable material, but gaskets could be more prone to damage or breakage during other repairs, so always use caution when working with this part. Allow the engine to cool completely and wear gloves when performing any engine repairs for hand protection.

This part can be used to replace a worn or broken rear stud to securely attach the shroud and keep it in place.Engine shrouds are critical for ensuring that air is properly circulated around the engine to keep it cool. Without an engine shroud overheating can occur quickly and cause serious engine damage. This rear stud is intended to attach the back of the engine shroud and secure it in place. This starter/shroud rear stud is a genuine replacement part that has been sourced directly from the manufacturer. This replacement starter/shroud rear stud fits various different models of MTD, Cub Cadet, Husky,Troy-Bilt, and Yardman outdoor power equipment such as lawnmowers, log splitters, and trimmers. Please note this starter/shroud rear stud is sold individually.

This is a cylinder head gasket that is located between the cylinder head and the engine block on many types of lawn and garden equipment. It is responsible for sealing the internal combustion process. It prevents oil and coolant from mixing together while each moves to the cylinder head from the engine block. If the cylinder head gasket is broken or damaged, it can cause fouled spark plugs, white smoke, milky white oil, leaking coolant, or an overheating engine.Gaskets can crack or wear out over time, which requires the parts to be replaced. Some of the tools needed to make the replacement include a gauge, socket driver, Torx screwdriver, nut driver, screwdriver, torque wrench, hex bit, and spark plug wrench. Make sure to wear work gloves and do the replacement with the tools on a flat surface.This cylinder head gasket is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold as an individual part. The head gasket is designed for use with lawnmowers, string trimmers, tillers, edgers, log splitters, and wood chippers created by Cub Cadet, Craftsman, and MTD.

The shear pin’s purpose is to stop the engine when it is broken. If the machinery hits something hard, the shear pin will break. This prevents injuries that could be fatal. If something large or small becomes clogged or jammed in the auger, the shear pin is meant to snap in half, rendering the auger useless. This happens once the auger reaches a certain point in pressure load, which also prevents damage to the rest of your equipment. The auger part of your machinery cannot turn without a shear pin. Since the purpose of the shear pin is to break on impact, it's a good idea to have several of these on hand for quick replacements. There’s nothing like having your equipment break down in the middle of a job. Repair is simple. Just remove the broken shear pin, line up the auger’s holes, and insert your new shear pin. Use the cotter pin to secure your shear pin. This genuine OEM auger shear pin works in conjunction with small engine equipment with augers made by Craftsman, Cub Cadet, MTD, Troy-Built, Yard Machines, and Yard-Man. This part is sold individually. Consider also ordering an MTD Pin-Bow Tie Cotter or retaining clip.

A carriage bolt is a type of fastener. It features a smooth rounded head and a square domed top. It has threading, which leads to up to the square shoulder. The purpose of its square is to prevent the bolt from spinning. Once the carriage bolt is inserted through the hole, using a nut and washer can provide additional security. Carriage bolts can corrode and loosen over time. Since it doesn't have a slotted head, a socket wrench is needed when replacing. This bolt carriage replacement is compatible with wood chippers, tillers, string trimmers, lawnmowers, and edgers. It is a genuine MTD product that measures 5/16x.075. It has a smooth rounded head and square shoulder underneath it. This carriage bolt is sold individually.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This is a genuine replacement for select walk-behind push lawn mowers. The hinged mulch cover is designed to replace the clippings chute that allows discharge so that the grass is more finely mulched in the machine. This part includes a metal hinge, which can break or snap over time. The plastic itself can also become damaged by debris or impacts, or simply crack due to age. Replacing the mulch cover with a genuine OEM model like this can be the ideal solution. If the cover is not replaced, the mulching feature will not be able to be used. This OEM replacement mulching cover is compatible with lawn mowers from MTD, Yard Machines, Yard Man, Troy-Bilt, Cub Cadet, Bolens, and Husky. This product includes the metal bracket and spring that are required for installation and securing the cover, sold as a single assembly. This hinged mulching cover can be used with 150+ lawn mowers from the brands listed above. No tools are required for this part replacement but it is important to be careful of pinch injuries when working with parts like this spring-hinged cover.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

In a snowblower, the driveshaft is connected to a part called a worm gear. The worm gear turns the auger blades which eject the snow. The worm gear is connected to the worm shaft, which causes the auger blade to turn rapidly. Eventually, the incredible torque inside the machine, plus the occasional bumps and bruises experienced by the machine in operation and when being stowed, may cause the worm gear to malfunction. When the snowblower is erratic in its operation and fails to remove snow completely, there is a good chance the problem is the worm gear. To replace the worm gear, remove the housing to get to the worm shaft. Remove the entire worm assembly. Next, remove the blower fan and remove the worm gear. Grease the auger assembly before installing the new gear. Reverse the order to reassemble. While the snowblower is disassembled, it's the best time so exam the auger, driveshaft, sheer bolts, and tires for wear. You may find other parts that need to be updated. Make sure to replace the worm bolt and any other necessary parts with a genuine OEM manufactured part such as this one. This gear can be used in a number of snowblowers, including machines made by Yard Machines, Craftsman, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, Ryobi, Montgomery Wards, Huskee, and MTD. Part sold individually.