Hinge Parts

Centers and positions the door hinge for proper alignment. Replaces worn, missing, or broken spacers that cause door sag, misalignment, or rubbing.

This door hinge provides the pivot point that lets the appliance door open smoothly and close flush. Replacing a worn or bent hinge restores proper alignment and sealing for safe, reliable door operation.

• Provides the pivot point that guides door opening and closing
• Helps keep the door square to the cabinet for a consistent seal
• Wear or damage can cause sagging, binding, gaps, or a door that won't close flush
• Restores smooth movement and proper door alignment

• Disconnect power before servicing; also shut off gas or water
• Support the door during removal to prevent damage or injury
• Transfer any mounting screws/brackets from the old hinge to the new one
• After installation, verify door alignment and gasket contact; adjust as needed

Lower door hinge secures the bottom corner of your refrigerator door and provides a pivot point for smooth opening and closing. Replace if cracked or worn.

Direct-fit door hinge for gas ranges. Supports and aligns the oven door for smooth opening and secure closing. Replace if worn, cracked, or broken.

Replacement door hinge assembly for side-by-side refrigerators. Mounts the door to the cabinet frame. Replace if cracked, bent, or worn for proper alignment.

Center hinge assembly that connects and supports refrigerator doors. Replace when hinge is cracked, broken, or causing door sagging and misalignment.

This top-closed thimble is a small protective plug that presses into a cabinet opening to cap and finish the hole, helping prevent abrasion and limiting air or moisture leaks for reliable appliance performance.

• Caps and seals an unused hole/opening in the liner or cabinet
• Shields edges to help protect nearby wiring or tubing from chafing
• Helps reduce drafts and moisture migration that can contribute to frost, condensation, or temperature swings
• Replace if cracked, brittle, loose, missing, or if you notice gaps or rubbing noises

• Disconnect power; if applicable, turn off the water supply
• Access the opening, remove the old thimble/plug, and clean the area
• Align and press the new thimble into the hole until fully seated and flush; avoid pinching wires or tubing
• Restore power/water and verify a snug fit

Secures and supports your dryer door, allowing smooth opening and closing. Replace if cracked, bent, or broken to restore proper door alignment and function.

Lower hinge bracket mounts at the bottom of your refrigerator cabinet to support and align the door. Replace if bent, cracked, or worn for proper alignment.

This is a door hinge for a range oven that connects the door to the oven frame, allowing it to open, close, and lock in place during the self-clean cycle. It uses a spring-loaded mechanism to hold the door at various open positions. Replace this hinge if the oven door drops down, won't stay open, closes unevenly, or is difficult to remove and reinstall.

Replacement door hinge for dishwashers. Supports and controls door movement for smooth opening and closing. Replace if bent, broken, or worn out.

Replacement hinge for wall oven doors. Installs at door pivot point to restore smooth opening and closing. Needed when original is cracked, worn, or broken.

This cover conceals the gap at the bottom of your refrigerator for a clean, finished appearance. Replace if the cover is damaged, missing, or doesn't fit properly, leaving unsightly gaps visible.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

Secures the dryer door to the cabinet and provides a smooth pivot point. Replace this hinge if bent, worn, or broken to restore proper door alignment.