Parts for Maytag MGR5775QDS: 01 - Cabinet Parts

Supports and guides your range's lower drawer for smooth sliding. Replace worn or broken rollers to restore easy operation and prevent binding or sagging.

Size: 8-32

Size: No. 8

Seals oven door to prevent heat loss and maintain consistent temperature. Replace if frayed, flat, or allowing smoke/heat to escape. Clips install easily.

Mounts to the oven frame to secure the door hinge arm. Replace if your oven door won't close fully or stays ajar. Restores proper heat seal and alignment.

Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Replacement screw for range and oven assemblies. Secures panels, brackets, and internal components. Order if original is stripped, missing, or damaged.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This door switch detects when the appliance door is closed and signals the control so the unit can start or run. Replacing a faulty switch restores proper door-sensing and safe operation. What it does:

• Detects door open/closed status and sends the signal to the appliance control
• Prevents the unit from starting or running if the door is open
• Commonly linked to symptoms like the appliance not starting, not completing cycles, or lights/controls behaving incorrectly
• Works as the safety interlock for door-dependent functions

• One door switch

• Disconnect power before servicing to avoid shock or injury
• Match connector style and mounting alignment to the original switch before final installation
• Handle the switch and wiring gently to avoid damage to terminals or harnesses

Range retainer clip secures components in place during operation. Replace if loose, broken, or missing to prevent rattling and ensure proper assembly.

Adjustable leveling leg that stabilizes and balances your range. Replace if cracked, broken, bent, or threads are stripped from wear or impact damage.

Rubber bumper stop cushions moving range parts to reduce vibration and noise. Replace if worn, cracked, or missing to restore proper spacing.

Black

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Lower

Replace missing or stripped screws for your range anti-tip bracket. This 2-piece hardware set secures the bracket to the wall or floor for stability.

Anti-tip bracket bolts to the floor behind your range to prevent tipping. Replace if missing, bent, or damaged during moving or installation.