Parts for Gaggenau KE282-6__: 01 - Complete Parts

This fast radiant cooktop element replaces a damaged or non-working surface burner to restore even, reliable heating on compatible electric glass-ceramic ranges. It's a direct-fit heating element designed for 4-wire connections. What it does:

• Heats cookware quickly via the radiant heating surface for stovetop cooking
• Replaces cracked, non-heating, or intermittently heating burners
• Restores consistent temperature response and even heat distribution
• Works with 4-wire cooktop wiring; matches OEM element size and mounting

• One fast radiant cooktop element (180 mm / 7 in., 4-wire)

• Disconnect power at the breaker before servicing the cooktop to avoid shock
• Handle glass-ceramic surfaces carefully to prevent cracking; lift element per your model's service instructions
• Match wire colors/terminals exactly and secure connections;
• Test cooktop function after installation and re-seat any trim or retainers per the manufacturer guide

This bolt serves as a hinge pin or mounting fastener for a microwave door hinge assembly. It secures the hinge mechanism to the microwave frame, allowing the door to pivot open and closed smoothly. Replace this bolt if the door feels loose, sags, or if the original bolt is stripped, corroded, or missing.

This is a rubber or silicone sealing grommet used to create an airtight seal around openings or connections within the microwave. It helps prevent moisture, heat, and air from escaping or entering where components pass through panels. Replace this part if you notice steam leaking from unusual spots, rattling noises near sealed areas, or visible cracking and deterioration of the original seal.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This is a right-side holder or endcap bracket that secures an internal component in place within the microwave. It provides structural support and proper alignment for the part it holds. Replace this holder if it is cracked, broken, or missing, which can cause the supported component to shift or rattle during operation.

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

A replacement control knob that restores user control for range/oven cooktops. Fits the listed Bosch control shafts to provide a solid grip and clear position feedback when the original knob is cracked, loose, or missing. What it does:

• Replaces a worn, cracked, or missing control knob so you can safely set heat levels and oven functions.
• Provides a secure fit on the control shaft for reliable on/off and temperature selection.
• Restores clear tactile and visual detents for accurate setting changes.
• Helps stop slipping or spinning knobs that prevent proper control.

• Disconnect power (or turn off gas supply for gas ranges) before replacing knobs.
• Most knobs pull straight off the shaft; gently pull while wiggling if needed. Do not force.
• If a retaining screw is present, loosen it first; keep hardware for reassembly.
• If the new knob does not fit, stop and verify shaft style and part number before forcing.

Range switch holder secures control switches in place. If switches are loose or falling out of the control panel, this holder may need replacement.

Bottom hinge for lawn tractor hood or deck assembly. Replace if hinge is bent, cracked, rusted, or no longer secures properly. Restores proper alignment.

This is an M4 x 10 DIN 7500 screw used for securing appliance components where a precision machine screw is required. It provides a simple replacement for worn or missing screws to restore proper assembly fit. What it does:

• Fastens panels, brackets, or small components using an M4 thread and 10 mm length
• Replaces stripped, corroded, or lost screws to stop rattling or loose parts
• Matches DIN 7500 geometry for consistent seating and reliable clamping force
• Suitable for indoor appliance environments when the correct material/finish is specified

• One M4 x 10 DIN 7500 screw

• Use the correct M4 driver and avoid over-torquing to prevent thread damage
• Replace only with identical size/grade screws when fastening safety-related components
• If a screw was part of an assembly, retain any washers or clips originally used