Parts for Maytag MGC4436BDB11: 02 - Burner Box, Gas Valves, And Switches, Optional Parts (Not Included) Parts

This grommet fits into a chassis or cooktop panel opening to cushion and seal where a shaft or component passes through. Replacing a worn grommet helps keep spills and debris out and restores a snug, quiet fit.

• Seals the opening to help prevent moisture and debris from entering the appliance chassis
• Centers and cushions the passing component to reduce vibration and rattling
• Helps maintain proper alignment and smooth operation of the control or related assembly
• Typical signs of wear: cracked or missing grommet, visible gap around the opening, loose/wobbly fit, evidence of spill intrusion

• Disconnect electrical power and, if applicable, shut off gas supply before servicing
• Remove knobs/bezels or access panels as needed to reach the grommet
• Lift out the old grommet and clean the opening of residue
• Press the new grommet fully into place without pinching; reassemble and test operation

This spark module controls the ignition spark for the cooktop burners so each burner lights reliably. Replacing a faulty module restores proper spark timing and helps the range ignite safely and consistently. What it does:

• Sends high-voltage sparks to the burner ignitors when the valve is opened
• Restores spark to burners that click but fail to light
• Can stop intermittent or no-spark conditions at one or more burners
• Works with the cooktop's control switches to coordinate ignition

• Disconnect power and shut off the gas supply before servicing
• Match wiring and connector positions exactly; take a photo before removal for reference
• Avoid touching ignition terminals; handle the module and wiring harness carefully

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This burner tube directs gas from the valve to the burner head so the cooktop lights and maintains a steady flame. It's a direct-fit service part that restores proper gas flow and burner performance. What it does:

• Channels gas safely from the valve to the burner head for ignition and steady flame
• Helps maintain even flame distribution across the burner
• Commonly replaced when burners won't light or flame is weak/uneven
• Supports correct burner assembly alignment for reliable operation

• One burner tube

• Turn off the gas supply and unplug the appliance before servicing
• Verify proper orientation and seating against the valve and burner head during installation
• Use basic hand tools; avoid damaging the tube or nearby components
• After installation, check for gas leaks with a soapy-water solution — do not use an open flame; if you smell gas, shut off supply.

This replacement valve switch assembly restores proper electrical control to the refrigerator's valve, helping re-establish reliable water/ice dispensing. It replaces a worn or faulty switch so the valve responds correctly to dispenser or ice-maker commands. What it does:

• Routes electrical signals to the valve so it opens and closes when the dispenser or ice maker calls for water
• Helps stop symptoms like no water or ice dispensing, intermittent dispensing, or a valve that won't actuate
• Replaces a failed or corroded switch assembly that can prevent the valve from responding
• Works as the control interface between the fridge wiring and the valve solenoid

• Always disconnect power and turn off the water supply before beginning service
• Take a photo or label wire connections before removing the old assembly to ensure correct reassembly
• Use basic hand tools; avoid forcing connectors — inspect wiring and connectors for damage and replace if necessary
• After installation, restore power and water, then test dispenser and ice-maker operation for proper function

This gas pressure regulator controls and stabilizes incoming fuel supply to the appliance's burner system, helping ensure consistent flames and reliable operation. Replace it if pressure is unstable or burners/oven won't heat or ignite correctly. What it does:

• Reduces household gas supply to the appliance-rated pressure for proper burner performance
• Maintains steady pressure as burner demand changes to prevent over/under-firing
• Helps prevent yellow, lifting, or flickering flames and sooting caused by pressure issues

• 1 gas pressure regulator

• Shut off gas supply and disconnect power before servicing
• Observe flow-direction arrow on the regulator body; install between supply and appliance manifold
• Use approved gas-rated thread sealant on threaded connections; do not overtighten
• After installation, check all joints for leaks with a non-corrosive leak-detection solution; correct any leaks before use

This burner tube directs gas from the oven manifold to the bake burner, ensuring a consistent flame for oven heating. It replaces a damaged or corroded tube to restore proper burner operation and heat distribution. What it does:

• Channels gas to the bake/broil burner for safe and consistent combustion
• Helps maintain even oven temperatures when functioning properly
• Can prevent burner misfires or poor ignition caused by holes, dents, or corrosion
• Often replaced when flames are weak, uneven, or the burner won't light reliably

• One replacement burner tube

• Turn off the appliance and shut off the gas supply before attempting any service
• Inspect gaskets and fittings; replace any damaged seals to prevent leaks
• Installation may require removal of oven liners or burner assembly

This burner tube replaces a damaged or corroded gas tube that routes fuel to the cooktop/oven burner, restoring proper gas flow and stable flames for reliable cooking. Designed as a direct-fit replacement when matched to your appliance model. What it does:

• Channels gas from the manifold to the burner so the burner can ignite and produce an even flame
• Helps maintain consistent flame pattern and heat distribution when functioning properly
• A damaged, dented or corroded tube can cause uneven flames, burner failure to light, or visible gas odor
• Use as a one-for-one replacement to restore safe, normal burner operation

• Shut off the appliance's gas supply and electrical power before servicing
• Remove nearby burner components and connectors carefully to access the tube; keep orientation for correct reassembly
• Inspect and replace any worn gaskets or fittings and ensure tight, leak-free connections when reinstalled

This snap-in bushing provides a low-profile bearing surface to support rotating shafts and reduce wear and noise in appliance assemblies. It restores smooth operation where the original bushing is worn or damaged. What it does:

• Provides a replaceable bearing/sleeve for rotating shafts and posts
• Reduces friction and wear on housing and moving parts
• Helps eliminate rubbing, grinding, or rattling noises during operation
• Maintains correct shaft alignment for smooth rotation

• One snap-in bushing

• Disconnect power before servicing and follow all safety instructions
• Access may require removing panels or covers; inspect surrounding parts for wear
• Press or snap the bushing squarely into the housing until fully seated; avoid deforming it
• Replace any damaged retainers or seals and test operation after reassembly

Size: 16 fl. oz.

This is a #10 x 2 inch appliance screw used to fasten panels and components in household appliances. It provides a simple, reliable hold to keep parts aligned and reduce vibration. What it does:

• Secures trim, panels, brackets, and internal components
• Helps prevent rattling or movement from loose or missing fasteners
• Restores proper alignment where a worn or missing screw causes gaps
• Works wherever a #10 x 2" fastener is specified by the manufacturer

• Disconnect power and water to the appliance before servicing
• Use the correct driver to avoid stripping the head; do not overtighten
• Keep track of removed fasteners and replace with identical-size screws
• Inspect mating threads and replace any damaged hardware

This tie-down bracket secures the appliance during installation so it stays firmly in place. It helps prevent shifting, vibration, or lifting for a solid, stable fit and reliable operation over time.

• Anchors the unit to its opening as designed, helping keep it stable
• Helps reduce movement, vibration, and rattling during use
• Replaces a bent, damaged, or missing bracket to restore a secure install
• Common signs: appliance shifts or rocks, visible gaps/misalignment, loose fit

• Disconnect power; shut off gas before servicing
• Install in the location/orientation specified by your product's installation instructions
• Reuse the model-specific mounting hardware or replace per your manual
• Tighten hardware securely but do not overtighten to avoid damage