Parts for Electrolux PCFD3670AFA: 02 - Control Panel / Top Burners Parts

This screw is a replacement fastener used to secure appliance panels and components, helping restore proper fit and reduce noise or movement from loose hardware. What it does:

• Secures panels, brackets or small components to prevent rattling and gaps
• Restores proper alignment for doors, control panels or interior parts
• Prevents parts from shifting or falling during operation
• Small replacement screw for routine hardware repairs

• Disconnect power or unplug the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Replace any missing or damaged screws to maintain safe operation

This spring restores proper tension to the refrigerator door hinge so the door opens and closes smoothly and stays aligned. It replaces a worn or broken hinge spring to reduce sagging and uneven door movement. What it does

• Provides hinge tension so doors close fully and seal properly
• Helps prevent door sag, misalignment, and uneven gaps
• Reduces grinding or rubbing noises from the hinge area
• Restores expected door operation after a broken or stretched spring

• One replacement hinge spring

• Disconnect power to the appliance before beginning any repair
• Use proper hand tools and keep fingers clear of the spring path; springs can release force suddenly
• Installation may require removing the door or hinge assembly; keep track of fasteners and alignment

Replace a faulty orifice if your gas range has uneven flames, yellow flames, or weak heat output. Controls gas flow to burners for proper combustion.

Secures internal components to the range chassis. Replace if bracket is bent, broken, or missing to restore proper alignment and stop rattling or sagging.

This electrical harness is a factory-style wire assembly that replaces a damaged or worn wiring connector group to restore power and signal routing. It reconnects controls and components so the appliance operates reliably. What it does

• Routes power and signal connections between control boards, switches, sensors and components.
• Restores interrupted circuits caused by broken, melted or corroded wires or terminals.
• Common symptom fixes: intermittent or no power to a component, controls not responding, or erratic operation.
• Maintains factory routing and connector fit to reduce stress and short risk when installed correctly.

• One electrical harness / wire assembly as shown.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Compare connectors and wire colors to the old harness to ensure correct replacement before installing.
• Secure harness away from moving parts, heat sources and sharp edges; use existing clips or fasteners.

This wiring harness connects multiple refrigerator electrical components to restore power and signals across controls, lights, fans, and motors. It replaces a damaged or worn harness to help return normal appliance operation. What it does

• Routes power and signal connections between the appliance control and internal components.
• Restores operation when a broken or shorted wire causes lights, fans, or compressor to not run.
• Helps stop intermittent electrical problems caused by frayed, corroded, or disconnected wires.
• Prevents shorts by replacing harnesses with exposed or damaged insulation.

• One assembled electrical wiring harness.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Verify connector orientation and gently press connectors fully until they click; do not force.
• Route harness away from moving parts and sharp edges; secure with existing clips or fasteners.

This electrical harness is a factory-style wiring connector assembly that delivers power and signals between refrigerator components for reliable operation and easy replacement. What it does:

• Routes power and signal connections to components such as fans, lights, valves and control modules
• Replaces damaged or corroded wiring that can cause intermittent failures or component loss of power
• Helps restore circuits that produce symptoms like no interior lights, non-running fans, or erratic component operation
• Uses OEM-style connectors and wire routing to match original installation

• Disconnect power at the appliance breaker or unplug the unit before starting
• Match connectors and routing to the original harness; do not force connectors or pinch wires
• Secure harness away from sharp edges and moving parts; use existing clips or straps

Fix unresponsive cycle selection or a range that won't change settings. This rotary selector switch restores reliable control panel operation.

This mounting bracket secures panels or components in place to restore proper alignment and reduce movement. Use it when an appliance panel, trim, or internal piece is loose or rattling. What it does:

• Provides a stable attachment point for a panel, trim, or internal component
• Prevents vibration and rattling caused by a failed or bent bracket
• Restores proper alignment to doors or access panels that sit unevenly
• Replaces damaged or broken mounting hardware to improve fit and finish

• Disconnect power and/or gas supply before starting work
• Access may require removing an outer panel or trim; keep fasteners organized
• Use basic hand tools; avoid overtightening to prevent stripping or damage

Fix weak flames or uneven heating with a new gas pressure regulator. Controls fuel flow to burners and oven for consistent cooking performance.

Mounting bracket that secures range components in place. Replace if cracked, broken, or missing to restore proper alignment and stability.

This is a replacement screw used to secure appliance panels and components so assemblies stay properly mounted and stable. It restores hardware that has become lost, stripped, or damaged. What it does:

• Fastens and secures panels, brackets, or trim pieces to the appliance
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment of covers and access panels
• Prevents further wear from unsecured components

• Disconnect power before servicing electrical appliances to avoid shock
• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent damage to threads or plastic parts
• Replace all matching fasteners for even fit