Parts for Electrolux GRFC2353AFA: 02 - Freezer Drawer, Baskets Parts

Forms an airtight seal around your refrigerator door to keep cold air in and prevent temperature loss. Replace if torn, cracked, or not sealing properly.

NOTE - Due to manufacturer changes gasket is only available in light grey and may differ from the photo shown.

The Outer Drawer Panel is an OEM part for Frigidaire freezers. It provides protection to the inner parts of the door. 

A bad freezer outer drawer panel can be caused by wear and tear, damage, or improper handling. When the outer drawer panel becomes faulty, it can result in issues such as difficulty in opening or closing the freezer drawer, compromised insulation, or an unsightly appearance.

Symptoms of a bad freezer outer drawer panel include:

• Difficulty in smoothly opening or closing the freezer drawer
• Poor insulation leading to temperature fluctuations
• Visible damage, cracks, or discoloration on the outer panel
• Aesthetic issues affecting the overall appearance of the freezer

Replace your faulty freezer outer drawer panel with this genuine OEM Frigidaire part to restore your freezer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Freezer Door Handle is an OEM part for Frigidaire refrigerators. It is responsible for facilitating easy access and opening of the freezer door. The handle is designed for comfort and a secure grip, allowing smooth operation of the door with minimal effort. 

Causes of a bad door handle can include normal wear and tear over time from frequent use, accidental damage from impact or mishandling, or components wearing down due to stress.  

Symptoms of a bad door handle include:

• Difficulty opening or closing the freezer door  
• The handle being loose, wobbly, or improperly secured
• Breakage or cracking of handle components
• Inability to open/close door without two hands

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement mounting screw secures trim, brackets, and panels inside your refrigerator. Restores proper fit when original screws are missing or stripped.

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

Single mounting screw secures trim, panels, or brackets inside your refrigerator. Replace lost, stripped, or damaged screws to keep components firmly attached.

Wire freezer basket installs in the freezer compartment to organize frozen foods. Replace a cracked, broken, or missing basket to restore storage space.

Secures trim, panels, and small components inside your refrigerator. Replace if cracked, broken, or missing to restore proper fit and eliminate rattling.

Drawer slide assembly for refrigerator storage bins. Enables smooth extension and retraction of drawers. Replace if cracked, broken, or causing binding.

This is the left-side slide rail assembly that supports and guides the lower freezer basket in bottom-freezer refrigerators. It mounts inside the freezer compartment and allows the basket to glide smoothly in and out. Replace this part if the freezer basket is difficult to slide, sits unevenly, or the rail is cracked or broken.

This upper freezer shelf assembly replaces a damaged or missing shelf to restore stable storage and organization in the freezer compartment. It provides a flat support surface so frozen items stay secure and organized. What it does:

• Replaces a cracked, warped or missing upper freezer shelf so food and containers sit level.
• Restores normal storage capacity and prevents items from falling or shifting during door movement.
• Reduces airflow obstruction that can occur when improvised shelves block vents.
• Helps keep the freezer interior organized and easier to clean.

• Remove all items from the freezer and move the door to an open, accessible position before installing.
• Slide the new shelf into the existing ledges or supports until it seats fully; do not force if it resists.
• If clips or brackets are used, ensure they are aligned and secure to avoid shift or drop.
• Follow the refrigerator's service manual for model-specific instructions; wear cut-resistant gloves if handling broken plastic or glass.

This replacement upper freezer shelf support secures the freezer's upper shelf so food stays stable and organized. It restores proper shelf alignment and prevents sagging or shifting that can block airflow or cause items to fall. What it does:

• Holds the upper freezer shelf firmly in place to maintain usable storage space
• Keeps frozen items level to prevent spills, tipping, and blocked airflow
• Replaces worn, cracked, or broken shelf support that causes shelf instability
• Helps restore correct shelf height and alignment after accidental damage

• One upper freezer shelf support bracket

• Disconnect power to the appliance before attempting any service to avoid injury
• Typically installs at the shelf mounting points; may snap or screw into place
• Inspect neighboring shelf clips and rails and replace if damaged for a secure fit

This part number contains one (1) screw.

Plastic partition that separates sections on a refrigerator shelf or in a deli drawer. Replace when cracked, broken, or missing to keep food organized.

Structural cabinet brace that stabilizes your refrigerator's interior frame. Replace if cracked, bent, or broken to restore proper alignment of doors.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Rubber door bumper cushions refrigerator door closure to reduce noise and protect cabinet finish. Replace if cracked, missing, or worn from repeated use.

Mounting bracket for refrigerators. Secures internal components in place. Replace if bracket is bent, cracked, or missing to restore proper support.

Support bar for refrigerator freezer drawer assembly. Installs between roller tracks to stabilize drawer and prevent shifting. Replace if broken or missing.

Refrigerator handle mounting block that secures door handles to the refrigerator door. Replace if cracked, broken, or missing to restore proper handle attachment.

Mounting screw secures shelves, panels, and brackets inside your refrigerator. Replace missing, rusted, or stripped screws to restore secure fit.

Mounting screw for refrigerator panels, handles, and internal components. Replace stripped, corroded, or missing screws to secure assemblies properly.

This replacement screw fastens appliance panels and trim to restore secure fit and reduce rattling or movement. Use it when a missing or damaged screw is causing loose parts or noisy operation. What it does:

• Secures panels, trim, or internal components to maintain proper alignment and stability.
• Stops rattling or vibration caused by loose or missing hardware.
• Helps prevent gaps that can catch on clothing or obstruct doors/drawers.
• Small hardware solution for common fit and finish issues.

• Disconnect power and any water supply before starting work.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Keep track of small parts and work on a stable surface; magnetic trays help.

Machine screw secures panels, trim, and internal brackets in your refrigerator. Replace worn, stripped, or missing fasteners to keep components aligned.