Parts for Electrolux ELTE7300AD0: 02 - Upper Cabinet / Drum Heater Parts

Secures the front panel to your washer frame. Replace this clip if your panel is loose, rattling, or won't stay in place due to a broken or missing clip.

If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.

Replace your dryer's exhaust duct assembly if cracked, damaged, or missing. Routes air from the dryer to the vent outlet for safe, efficient operation.

If your dryer drum won't turn or makes grinding noises, a worn drive shaft may be the cause. This metal shaft transfers motor torque to rotate the drum.

Replacement drum support roller wheel assembly for dryers. Installs on bulkhead to support and guide drum rotation. Replace when worn, cracked, or loose.

Positioning spacer that maintains proper gaps between dryer components. Replace if cracked, broken, or missing to prevent parts from rubbing together.

Metal mounting nut secures panels, brackets, and assemblies on your dryer. Replace if cracked, stripped, missing, or causing loose components.

Secures internal components in your dryer. Replace this mounting bracket if cracked, broken, or missing to restore proper alignment and stability.

Replace your dryer's drum assembly if it's cracked, dented, or worn. This rotating cylinder holds and tumbles clothes during the drying cycle.

Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.

Replaces cracked or broken air flow deflector baffle inside your dryer drum. Guides internal airflow for proper ventilation and cooling performance.

White molded baffle that lifts and tumbles laundry inside the dryer drum. Replace if cracked, broken, or missing to restore proper load movement.

Fix poor drying or overheating caused by restricted airflow. This air duct assembly routes hot air through your dryer to restore proper circulation.

Traps lint before it enters the exhaust system. Replace if damaged, torn, or causing lint buildup. Confirm fit with your dryer's model number.

Replace your dryer door gasket to restore an airtight seal and improve drying efficiency. Install when gasket is torn, cracked, or allows air leaks. Confirm fit with your model number before ordering.

This is a door switch that detects whether the dryer door is open or closed. When the door is shut, the switch completes the circuit and allows the dryer to run. Replace this switch if the dryer does not start when the door is closed, stops mid-cycle unexpectedly, or the drum light does not turn on or off properly when the door is opened and closed.

Dryer not starting or shutting off mid-cycle? A faulty wire harness disrupts electrical signals to motors, heating elements, and controls. Moderate DIY repair.

Dryer door won't stay closed or latch properly? This door latch assembly secures your dryer door during operation. Simple DIY fix with just two screws.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Replacement door glass for dryer doors. Provides a clear viewing window to monitor laundry during cycles. Order when glass is cracked, broken, or missing.

Secures dryer vent hose connections to prevent air leaks and maintain proper airflow. Replace if rusted, cracked, or loose. Confirm fit with your model.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Plastic cap cover for dryer installation. Replaces cracked, broken, or missing covers. Snaps into place to provide clean finished appearance.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Mounting screw secures panels, brackets, and internal components in your dryer. Replace if missing, stripped, or damaged during repairs or maintenance.

Replacement mounting screw for dryers. Secures panels and internal components. Needed when original screw is stripped, damaged, missing, or causing loose parts.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.

Clear outer window for dryer doors. Provides visibility into the drum during operation. Replace if cracked, scratched, or broken for safety and aesthetics.

Hex washer head ,10-32 x 0.375. Ground

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic