Parts for Electrolux E32AR85PQSE: 03 - Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Door breaker trim kit with corner pieces for freezers. Installs along door edges to protect and seal. Replace if cracked, broken, or missing pieces.

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

The Hinge-Lower is an OEM replacement part for Frigidaire refrigerators. It is the bottom hinge that attaches the freezer door to the refrigerator body, allowing smooth opening and closing of the door. As a moving part, these hinges endure stress and wear from frequent use over the lifespan of the appliance.

Causes of a bad lower hinge can include repetitive opening and closing cycles that degrade lubrication over time. General wear and tear or physical impacts that bend or warp the hinge assembly will reduce function.  

Symptoms of a bad lower hinge include: 

• Door not sitting flush or securely closing  
• Loose or sagging door that does not stay in position  
• Noisy “creaking” sounds when opening or closing
• Visible damage or separation of hinge components

This OEM Frigidaire replacement hinge is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement refrigerator drain hose routes defrost and condensation water from the freezer/drip pan to the drain tray to prevent pooling and ice buildup. It restores proper drainage to help keep the cabinet dry and working reliably. What it does

• Channels defrost and condensation water away from the evaporator and cabinet to the drain pan
• Helps prevent water pooling under or inside the refrigerator
• Reduces risk of ice buildup in the freezer or drain area caused by clogged or damaged hoses
• Works with the unit's drain system and clamps to maintain a watertight connection

• One replacement drain hose

• Disconnect power and water supply before starting any repair
• Remove access panels or shelving as needed to reach the hose and drain area
• Replace clamps and check for proper seating to prevent leaks; avoid kinking or sharp bends

Collects defrost water from the evaporator and channels it to the drain system. Replace if cracked, broken, or missing to prevent leaks inside the cabinet.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Replacement cabinet corner trim for freezers. Restores the finished edge where the original trim piece has cracked, broken, or gone missing. Easy install.

Specs: Hex head ,1/4-20 x 5/8

Replacement glass panel for refrigerator shelves. Restores a smooth surface when original is cracked, broken, or missing. Fits shelf assemblies.

Transparent glass shelf for refrigerator food storage. Replace if cracked, broken, or shattered from heavy loads or accidental drops. Direct fit part.

Replace your cracked or broken refrigerator door bin. This storage bin attaches to the inside of your refrigerator door to hold beverages and condiments.

Replacement freezer drawer restores organized storage in your refrigerator. Replaces cracked, warped, or missing drawer for proper sliding function.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Replacement mounting screw for freezer panels, trim, and brackets. Needed when original fastener is missing, stripped, or damaged during repairs.

This breather valve regulates air pressure between the freezer compartment and the outside environment, allowing the door to open easily after the compressor cycles. It prevents a vacuum from forming inside the freezer as the air cools and contracts. Replace this valve if the freezer door is difficult to open shortly after closing or if you hear unusual hissing sounds from the freezer.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Mounting bracket that secures freezer shelves and internal panels. Replace if cracked, bent, or broken to restore proper alignment and stability.

Guide rail that supports and directs refrigerator drawers along their track. Replace when original is worn, cracked, or broken to restore smooth sliding.

Replacement drawer slide for freezers. Restores smooth gliding when original is broken, worn, or causes sticking. Essential for proper drawer alignment.

Supports and guides the crisper drawer for smooth sliding. Replace if cracked, broken from stress, or if drawer no longer sits securely in refrigerator.

A replacement stainless-steel trim kit that restores the finished look around your appliance for a clean, built-in appearance. Helps cover gaps and damaged edges and keeps the front area looking uniform. What it does

• Replaces damaged or missing exterior trim pieces to improve appearance.
• Covers gaps between the appliance and surrounding cabinetry for a finished look.
• Helps maintain a consistent stainless-steel exterior finish.
• Commonly used when original trim is bent, scratched, or otherwise cosmetically worn.

• Designed for exterior attachment; your appliance's installation manual for exact placement and hardware requirements.
• Turn off power to the appliance (or follow manufacturer safety instructions) before starting work.
• Use proper tools and handle stainless panels carefully to avoid scratching the finish.
• If fasteners or additional trim supports are required, order separately.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.