Parts for Maytag GB5525PEAS10: 03 - Freezer Door Parts

Color: Stainless

The Freezer Door Handle is an OEM part for Whirlpool refrigerators. It provides a sturdy grip for opening and closing the freezer door, ensuring easy access to the freezer compartment. 

Causes of a bad freezer door handle can include normal wear and tear, repeated use, or accidental damage. 

Symptoms of a bad freezer door handle include:

• The handle feeling loose or wobbly
• Cracks or visible damage to the handle
• Difficulty in opening or closing the freezer door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This door gasket runs around the perimeter of the door opening to create a dependable seal when closed. A proper seal helps limit air and moisture leaks, supporting stable internal conditions, reduced condensation, and efficient performance. What it does:

• Seals the door perimeter to block unwanted air and moisture infiltration
• Helps minimize condensation around the door and maintain consistent internal conditions
• Replaces gaskets that are torn, cracked, warped, or permanently compressed
• Can help when the door won't seal properly or you notice drafts, moisture, or temperature swings

• 1 door gasket

• Disconnect power if removing the door or working near electrical components
• Warm the gasket (soak in warm water or use low heat) to relax it before installation
• Press the gasket fully into the channel/retainer, ensuring corners are completely seated
• Check for uniform contact all around; adjust door alignment if needed and allow up to 24 hours for the gasket to conform

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This vent plug seals an unused appliance vent opening to keep out debris and improve appearance. A simple OEM-fit replacement that restores a clean, finished look to the appliance exterior. What it does

• Covers and seals a vent opening to prevent dust, lint, and pests from entering the cabinet or vent cavity.
• Restores the appliance's finished appearance where a vent opening is exposed or a plug is missing.
• Helps maintain proper airflow paths by closing unused ports and reducing drafts.
• Fits the original mounting location for a secure, low-profile fit.

• One black vent plug.

• High-level push-in replacement; no special tools typically required.
• Disconnect power to the appliance before any service when accessing internal areas.
• Inspect surrounding trim or grille for clips or screws; remove carefully to access the vent opening.
• If plug does not seat fully, verify the correct OEM location and orientation before forcing.

This white door stop limits how far the door swings open, helping protect hinges and nearby surfaces. Replace a worn or missing stop to restore the intended opening range and smooth, controlled door movement.

• Limits door swing to prevent overextension and impact
• Helps protect door hinges and surrounding cabinetry
• Restores proper opening range when the original stop is cracked or missing
• Common signs: door opens too wide, door hits adjacent surfaces, visible broken/missing stop

• Disconnect power and clear items from the door before service
• Support the door to prevent strain on the hinges
• Remove hinge cover and fasteners as needed, swap the stop, and reassemble
• Open and close the door to verify proper swing and gasket seal

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This freezer door retainer is a small mounting clip that secures the freezer door/inner panel and helps keep the door aligned for a proper seal. Replaces a broken or worn retainer to restore reliable door positioning and reduce air leaks. What it does:

• Secures the freezer door or inner door panel to the cabinet or hinge assembly
• Helps maintain proper door alignment for an effective freezer seal
• Common fix when the door drops, pulls away, or creates a visible gap
• Prevents unnecessary cold air loss from a misaligned or loose door

• One freezer door retainer

• Disconnect power before beginning repairs and follow manufacturer safety instructions
• Access may require removing the freezer door or inner panel and existing fasteners
• Inspect surrounding hinge and mounting hardware for wear and replace if needed