Parts for Maytag MBF1958WEB0: 03 - Freezer Door Parts

This door handle assembly replaces a damaged or worn handle to restore secure grip and normal door operation. It gives a finished look and lets you open and close the door confidently. What it does:

• Provides a sturdy replacement for a cracked, loose, or broken door handle
• Restores proper leverage so the door opens and closes smoothly
• Prevents further damage to the door front from a failing handle
• Matches original mounting points for a direct-fit replacement

• One door handle assembly

• Disconnect power to the appliance before beginning any repair
• Remove the door trim or access screws to reach the handle mounting hardware
• Reinstall using original screws and hardware; do not force or overtighten

This white replacement door handle restores a fridge door's grip and appearance, letting you open and close the door smoothly while matching white appliance trim. It's a direct-fit replacement for the original handle. What it does:

• Provides a secure grip for opening and closing the refrigerator door
• Restores damaged, cracked or discolored handles to like-new appearance
• Replaces worn or broken mounting points that prevent proper door operation
• Helps maintain the door's alignment and everyday usability

• Remove power or secure the appliance to prevent movement before starting
• Access may require removing door trim or end caps—keep fasteners for re-use
• Use hand tools only; avoid overtightening screws to prevent cracking

This replacement refrigerator door handle restores safe, secure grip and normal door access after a worn or broken handle. It matches OEM fit and finish to keep the door looking and functioning like new. What it does:

• Provides a secure handhold to open and close the refrigerator door
• Replaces cracked, loose, or missing handles that affect door operation or appearance
• Maintains proper clearance and alignment for normal door movement
• Helps prevent injury from sharp or broken handle edges

• Use the appliance power and water disconnect procedure recommended by the manufacturer before beginning work
• Remove trim or screws as needed to access handle fasteners; keep fasteners for reassembly unless new hardware is explicitly included
• Tighten screws evenly to avoid misalignment or cosmetic damage
• If door or trim is bent or damaged, inspect assemblies before installing the new handle

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This door gasket runs around the perimeter of the door opening to create a dependable seal when closed. A proper seal helps limit air and moisture leaks, supporting stable internal conditions, reduced condensation, and efficient performance. What it does:

• Seals the door perimeter to block unwanted air and moisture infiltration
• Helps minimize condensation around the door and maintain consistent internal conditions
• Replaces gaskets that are torn, cracked, warped, or permanently compressed
• Can help when the door won't seal properly or you notice drafts, moisture, or temperature swings

• 1 door gasket

• Disconnect power if removing the door or working near electrical components
• Warm the gasket (soak in warm water or use low heat) to relax it before installation
• Press the gasket fully into the channel/retainer, ensuring corners are completely seated
• Check for uniform contact all around; adjust door alignment if needed and allow up to 24 hours for the gasket to conform

Factory-style replacement screw for securing appliance components. Restores a tight, rattle-free fit for brackets, panels, trims, or covers when the original hardware is missing, stripped, or corroded, helping keep assemblies aligned and secure.

• Fastens components to keep panels, brackets, and trim firmly in place
• Replaces missing, stripped, or rusted hardware that can cause looseness or rattling
• Helps restore proper alignment of parts that won't stay secured
• Useful after service when original fasteners are damaged or lost

• Disconnect power before servicing; shut off water supply if applicable
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking adjoining parts

The Threaded Handle Anchor is an OEM part for Whirlpool refrigerators. This component is essential for securely attaching the refrigerator door handle to the door, ensuring that it remains firmly in place during regular use. The anchor fits into the door and provides a threaded connection point for the handle screws, offering stability and ease of use.

Common causes of a bad threaded handle anchor include wear and tear from frequent use, cross-threading during installation, or physical damage from excessive force or impact.

Symptoms of a bad threaded handle anchor include:

• The refrigerator door handle feeling loose or unstable
• Difficulty securing the handle to the door
• The handle detaching from the door
• Visible damage or stripping on the anchor threads

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.