Parts for Maytag MBF1958WEB0: 05 - Refrigerator Door Parts

Color: clear. Measures about 11 inches wide by 7 inches high.

Replace a cracked or missing dairy tray on your refrigerator door. This door bin restores a dedicated spot for butter and small items so they stay organized and easy to reach while maintaining a secure fit on the door.

• Mounts on the refrigerator door as the dairy compartment tray
• Holds butter, cheese, and other small items securely
• Restores proper fit when the original tray is cracked, warped, or missing
• Common symptoms: broken tabs, tray falls off, loose/wobbly fit, items spilling when the door opens

• Open the door, lift the old tray straight up and out; align the new tray with the door slots and lower until fully seated
• Handle plastic parts gently and avoid forcing; allow parts to warm to room temperature to reduce risk of cracking
• Confirm both sides are fully engaged before loading items

This small refrigerator door bin replaces a cracked or missing shelf bin to keep cans, bottles and small items organized on the door. It restores safe storage and helps prevent spills and shifting during door use. What it does:

• Provides a secure shelf on the refrigerator door for cans, condiments and small containers
• Keeps contents contained to reduce spills and items falling when opening the door
• Replaces cracked, split or warped bins that no longer hold items securely
• Fits into the door rail to restore original storage layout

• Remove food and lift out the old bin; align new bin with the door rails and slide in until it seats
• No tools required for most installations, but handle carefully to avoid chipping plastic
• Do not overload the bin—excess weight can damage the bin or door rail

This medium refrigerator door bin restores secure storage on the fresh food door. Replace a cracked or missing bin to keep bottles and condiments upright and accessible; it snaps into the door liner for a snug, factory-style fit.

• Mounts to the refrigerator door to hold everyday items securely
• Helps keep bottles and jars upright and organized
• Replaces bins that are cracked, warped, or missing
• Addresses issues like loose fit, broken tabs, or items falling when the door opens

• Remove contents and lift out the damaged bin
• Align the new bin's tabs with the door liner slots and press down until fully seated
• Verify a secure fit before loading items
• If removing additional door components for access, disconnect power for safety

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This door gasket seals the dishwasher door opening to keep wash water and moisture inside the tub. A fresh, flexible seal helps prevent leaks and improves cleaning performance by maintaining proper pressure and heat.

• Creates a watertight seal between the tub and door perimeter
• Helps prevent leaks at the bottom and sides of the door
• Helps resolve symptoms like water on the floor, moisture around the door, long dry times, or visible tears/flattening of the old gasket
• Restores proper door compression and wash chamber containment

• Disconnect power and turn off water supply before service
• Remove the old gasket from the channel; clean the groove of debris and residue
• Press the new gasket evenly into the channel, centering at the top and working down both sides
• Close the door to help seat the gasket; a short run cycle may help it conform

This door handle assembly replaces a damaged or worn handle to restore secure grip and normal door operation. It gives a finished look and lets you open and close the door confidently. What it does:

• Provides a sturdy replacement for a cracked, loose, or broken door handle
• Restores proper leverage so the door opens and closes smoothly
• Prevents further damage to the door front from a failing handle
• Matches original mounting points for a direct-fit replacement

• One door handle assembly

• Disconnect power to the appliance before beginning any repair
• Remove the door trim or access screws to reach the handle mounting hardware
• Reinstall using original screws and hardware; do not force or overtighten

This white replacement door handle restores a fridge door's grip and appearance, letting you open and close the door smoothly while matching white appliance trim. It's a direct-fit replacement for the original handle. What it does:

• Provides a secure grip for opening and closing the refrigerator door
• Restores damaged, cracked or discolored handles to like-new appearance
• Replaces worn or broken mounting points that prevent proper door operation
• Helps maintain the door's alignment and everyday usability

• Remove power or secure the appliance to prevent movement before starting
• Access may require removing door trim or end caps—keep fasteners for re-use
• Use hand tools only; avoid overtightening screws to prevent cracking

This replacement refrigerator door handle restores safe, secure grip and normal door access after a worn or broken handle. It matches OEM fit and finish to keep the door looking and functioning like new. What it does:

• Provides a secure handhold to open and close the refrigerator door
• Replaces cracked, loose, or missing handles that affect door operation or appearance
• Maintains proper clearance and alignment for normal door movement
• Helps prevent injury from sharp or broken handle edges

• Use the appliance power and water disconnect procedure recommended by the manufacturer before beginning work
• Remove trim or screws as needed to access handle fasteners; keep fasteners for reassembly unless new hardware is explicitly included
• Tighten screws evenly to avoid misalignment or cosmetic damage
• If door or trim is bent or damaged, inspect assemblies before installing the new handle

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This white door stop limits how far the door swings open, helping protect hinges and nearby surfaces. Replace a worn or missing stop to restore the intended opening range and smooth, controlled door movement.

• Limits door swing to prevent overextension and impact
• Helps protect door hinges and surrounding cabinetry
• Restores proper opening range when the original stop is cracked or missing
• Common signs: door opens too wide, door hits adjacent surfaces, visible broken/missing stop

• Disconnect power and clear items from the door before service
• Support the door to prevent strain on the hinges
• Remove hinge cover and fasteners as needed, swap the stop, and reassemble
• Open and close the door to verify proper swing and gasket seal

This shelf trim is the molded edge piece for your refrigerator shelf. It snaps in place to restore a clean, secure lip that helps keep items in place and limits spills from reaching shelves below. What it does:

• Attaches to the edge of a refrigerator shelf to create a finished barrier
• Helps retain items and contain minor spills
• Restores stability when the original trim is cracked or missing
• Common symptoms: broken or loose trim, items sliding off the shelf, trim won't stay attached

• 1 shelf trim

• Disconnect power and remove food from the affected shelf before servicing
• Lift out the shelf or bin and place it on a flat, protected surface
• Release the old trim's tabs and slide or unsnap it from the shelf—avoid forcing or flexing
• Align the new trim and press until fully seated; reinstall the shelf or bin

This door hinge bushing restores smooth, stable movement at the refrigerator door pivot. It sleeves the hinge pin to reduce friction and wear, helping the door stay aligned so it closes cleanly and maintains a proper seal.

• Seats in the door hinge to guide the hinge pin and reduce friction
• Helps maintain door alignment and consistent gasket contact
• Replaces a worn, cracked, or missing bushing that can cause noise or binding
• Typical symptoms: squeaking or grinding at the hinge, door sagging/misalignment, door hard to open or close, or not closing flush

• Disconnect power; clear and support the door to prevent strain
• Remove hinge cover and fasteners; lift the door off the hinge pin as needed
• Remove the old bushing from the hinge area and press the new bushing fully into place, matching original orientation
• Reinstall hardware; adjust hinges/level as needed

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

Color: Black

The Door Closure is an OEM replacement part for Whirlpool refrigerators. It is a small component that the door rides on that allows it to open and close properly.

Causes of impaired operation involve age-related spring coil fatigue, dislodged or cracked plastic housing pieces, or confined door alignment stripping closure grooves.

Symptoms of a faulty closure include:

• Cool air escaping around door edges driving up energy costs
• The fridge unable to maintain set interior temperatures
• Inability to securely latch doors closed

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Door Closure is an OEM part for Whirlpool refrigerators. It is a critical component responsible for ensuring the proper sealing and closure of the refrigerator door, maintaining the desired temperature and preventing air leaks.

A faulty or worn door closure can lead to issues such as inadequate cooling, increased energy consumption, and potential food spoilage. Causes of a bad door closure may include normal wear and tear over time, physical damage from impact or mishandling, or compatibility issues with the specific refrigerator model.

Symptoms of a faulty Door Closure include:

• Air leaks around the door seal, causing cooling inefficiency
• Difficulty in opening or closing the refrigerator door
• The door not sealing tightly or feeling loose when closed
• Visible cracks, breaks, or damage to the door closure mechanism

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

Factory-style replacement screw for securing appliance components. Restores a tight, rattle-free fit for brackets, panels, trims, or covers when the original hardware is missing, stripped, or corroded, helping keep assemblies aligned and secure.

• Fastens components to keep panels, brackets, and trim firmly in place
• Replaces missing, stripped, or rusted hardware that can cause looseness or rattling
• Helps restore proper alignment of parts that won't stay secured
• Useful after service when original fasteners are damaged or lost

• Disconnect power before servicing; shut off water supply if applicable
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking adjoining parts

The Threaded Handle Anchor is an OEM part for Whirlpool refrigerators. This component is essential for securely attaching the refrigerator door handle to the door, ensuring that it remains firmly in place during regular use. The anchor fits into the door and provides a threaded connection point for the handle screws, offering stability and ease of use.

Common causes of a bad threaded handle anchor include wear and tear from frequent use, cross-threading during installation, or physical damage from excessive force or impact.

Symptoms of a bad threaded handle anchor include:

• The refrigerator door handle feeling loose or unstable
• Difficulty securing the handle to the door
• The handle detaching from the door
• Visible damage or stripping on the anchor threads

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.