Parts for Ge NVLR333GV0AA: 03 - Front Panel, Door, Gas Valve & Burner Asm. Parts

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Captures lint and debris during drying cycles. Replace when torn, damaged, or allowing lint buildup. Confirm fit using your dryer's model number.

A fabric strip that seals the gap between the dryer drum and front panel to prevent air leaks. Replace if you notice lint escaping from the front of the dryer, reduced drying efficiency, or if the seal is visibly worn or damaged.

Supports smooth drum rotation in your dryer. Replace when you hear squeaking or grinding noises during operation. Sold individually; most models use 3-4. Confirm fit with your model number.

Supports and stabilizes the dryer drum during rotation. Replace when you hear squeaking noise or notice excessive drum wobble. Verify fit with your model.

The Handle Door is an OEM part for GE dryers. This door handle allows for easy opening and closing of the dryer door, providing a secure grip to access the drum.  

Common causes for door handle failure include regular wear from frequent use, forceful handling, and material fatigue over time.  

Symptoms of a failing Handle Door include:

• Cracks or breakage in the handle
• Handle becoming loose or detaching from the door
• Difficulty in opening or closing the dryer door
• Visible wear that could affect the grip or usability

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Meters gas flow to the dryer burner. Replace if damaged, clogged, or when converting between natural gas and LP. Installs at the burner assembly.

This is a safety device installed in the gas supply line of a gas dryer that restricts gas flow in the event of a leak or line disconnection. It helps prevent dangerous gas accumulation by limiting the amount of gas that can escape. Replace the leak limiter if your dryer has difficulty igniting, produces a weak flame, or if a gas technician identifies it as faulty during a safety inspection.

Dryer won't heat or you smell gas? The gas valve controls fuel delivery to the burner. Common fix for heating failures and gas leaks. Moderate DIY repair.

This valve elbow redirects the appliance's water line to the inlet valve, providing a secure 90° connection to help prevent kinks and ensure consistent water flow. Simple, compact replacement for a worn or damaged elbow. What it does

• Redirects the water supply line to the appliance inlet valve for a neat, low-profile connection
• Helps prevent kinking or strain at the inlet connection that can lead to leaks
• Restores proper water routing when the original elbow is cracked, broken, or leaking
• Resolves symptoms such as visible leaks at the valve connection or reduced/disrupted water flow to dispensers or ice makers

• Turn off water supply and unplug the appliance before beginning work
• Drain residual water from the line before removing the old elbow to minimize spills
• Inspect the inlet fittings and water line for damage; replace any worn tubing or gaskets
• Use appropriate tools and replacement gaskets; hand-tighten fittings and check for leaks after restoring water

Fix a dryer that won't heat or cycles but doesn't ignite with this gas burner assembly. Restores consistent flame when the original is corroded or clogged.

The Igniter is an OEM part for GE dryers. It is designed to ignite the gas burner to produce heat, which is essential for drying clothes. The igniter ensures that the gas is lit efficiently and safely, enabling the dryer to reach and maintain the proper temperature for effective drying.

You should replace the igniter if it becomes faulty. Causes of a bad igniter can include electrical failures, cracks or breaks in the igniter material, or wear and tear from regular use. These issues can prevent the igniter from generating the necessary heat to ignite the gas.

Symptoms of a bad igniter include:

• The dryer not heating up
• Extended drying times
• The igniter glowing but failing to light the gas burner
•  A lack of flame in gas dryers

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A dual coil gas valve controls the flow of gas to your appliance's burners using two electromagnetic coils to open and close the valve. It regulates gas delivery to maintain safe, consistent flame operation. Replace this part if your burner won't light, gas flow won't shut off, or you notice uneven flames or a gas smell during operation.

Hex washer head screw for refrigerators, freezers, and other appliances. Replaces lost, stripped, or damaged screws during repairs or panel assembly.

The gas valve solenoid controls gas flow to the dryer's burner assembly for heating during drying cycles. Located near the gas valve, replace it when the dryer won't heat, heats intermittently, or won't ignite properly.

Black. 8-18 AB HXW 3/8