Parts for Gaggenau EB965-610: 03 - Internal Top Panel & Fascia Panel Parts

This is a cutting disc used in range and oven assemblies. It serves as a component in the internal mechanism of the appliance. Replace this disc if it shows signs of wear, cracking, or damage that affects the operation of the associated assembly.

This is a door-actuated switch used in an oven or range to detect whether the door is open or closed. It signals the control board to enable or disable certain functions such as the oven light or self-clean lock mechanism. Replace this switch if the oven light stays on or off regardless of door position, or if the appliance does not recognize when the door is opened or closed.

This insulating paper is a thin non-conductive sheet used to protect wiring, terminals, and components from heat and accidental electrical contact. It helps prevent shorts and keeps sensitive parts shielded from nearby hot surfaces. What it does:

• Provides heat and electrical insulation between components and chassis or heating elements
• Reduces risk of electrical arcing and short circuits caused by contact with metal parts
• Protects wiring and terminals from chafing, heat damage, or direct exposure to hot surfaces
• Helps restore original factory clearances and insulation when replacing worn or damaged material

• Insulating paper

• Disconnect power before servicing
• Replace only in the same position and orientation as the original part; confirm fit before final reassembly
• Use caution handling sharp metal edges and hot components; wear gloves and eye protection as needed
• If routing or adhesives are part of the repair, use only manufacturer-recommended methods and materials

This fixing angle is a small metal mounting bracket that secures panels or components in place, restoring proper fit and reducing vibration. It's a direct-replacement part used where a bent or broken bracket causes misalignment. What it does:

• Secures appliance panels, trim, or assemblies to the frame to maintain alignment and stability
• Restores proper panel fit to stop rattling, rubbing, or gaps
• Replaces bent, cracked, or missing brackets that prevent components from seating correctly
• Works as a mechanical anchor for screws or fasteners where the original bracket was installed

• Disconnect power and water before starting any repair
• Use basic hand tools; remove the panel or access cover to reach the bracket
• Keep track of fasteners and their locations for correct reassembly
• Wear gloves and eye protection; avoid forcing parts to prevent further damage

This adhesive ground terminal label identifies the appliance's designated grounding connection, helping homeowners locate the correct terminal quickly for safe wiring and service. Durable, self-adhesive marking for internal appliance panels. What it does:

• Marks the chassis ground/earth connection so the grounding point is clearly visible
• Helps reduce wiring errors during service or installation
• Improves safety by making the ground terminal easy to find
• Intended for use on interior appliance sheet metal or electrical access panels

• Disconnect power before opening access panels or working near electrical components
• Clean and dry the mounting surface; peel adhesive backing and press firmly into place
• Position carefully before applying; adhesive is permanent and not intended for repeated repositioning
• Use only on appropriate interior panel surfaces away from high-heat components

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

This wiring harness cable connects electrical components inside the appliance to restore or maintain power and control signaling. It replaces a damaged or worn cable to help resolve intermittent power, unresponsive controls, or communication faults. What it does:

• Carries power and/or control signals between internal modules and components
• Replaces frayed, pinched, or broken wiring that can cause intermittent operation
• Helps stop failures that produce no power to a circuit or erratic device behavior
• Restores proper connector fit when insulation or terminals are damaged

• Disconnect all power before starting any repair to avoid shock or damage
• Route the cable as shown in the appliance harness path and secure any retaining clips or ties
• Ensure connectors are fully seated and locked; do not force mismatched plugs

This is a replacement cable labeled EB 964/965 - 610 used to restore a damaged or worn wiring connection in compatible Bosch appliances. Replacing a faulty cable can stop intermittent operation and help return the appliance to normal function. What it does:

• Provides the factory wiring connection for the EB 964/965 circuit or assembly
• Transmits power and/or control signals as part of the appliance's internal wiring
• Replaces frayed, cut, burnt, or corroded cable that causes intermittent operation or failure to operate
• Helps eliminate related error codes or symptom behavior caused by an open or shorted cable

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle connectors gently and route the cable to follow original clips and strain-relief points
• Verify secure, fully-seated connections and inspect surrounding insulation for damage

This control module manages all electronic functions and operations of your oven including temperature regulation, timing, and cooking modes. It processes user inputs and controls heating elements, fans, and other oven components to maintain precise cooking conditions. Replace it when the oven won't heat, temperature is inaccurate, or when control functions become unresponsive.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.