Parts for Crosley CDU2J: 03 - Pump & Motor Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

The pump and motor assembly is the combined unit in your dishwasher or washing machine that circulates and drains water during operation. The motor drives the pump to move water through the system at the right pressure and timing. Replace this part if your appliance is not draining, water is pooling at the bottom, or you hear a loud grinding or humming noise during a cycle.

(SOLENOID NOT AVAILABLE MUST ORDER ICE DOOR KIT 12001991)

(SOLENOID NOT AVAILABLE MUST ORDER ICE DOOR KIT 12001991)

Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.

Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Replace your dishwasher shaft seal to stop leaks around rotating components. Restores watertight protection for bearings and internal parts. Verify fit.

(SOLENOID NOT AVAILABLE MUST ORDER ICE DOOR KIT 12001991)

This dishwasher drain lifter helps move water through your dishwasher's drainage system during the wash and rinse cycles. It ensures proper water circulation and prevents standing water from remaining in the bottom of the tub. Replace when you notice water pooling in your dishwasher after cycles complete or poor drainage performance.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

(SOLENOID NOT AVAILABLE MUST ORDER ICE DOOR KIT 12001991)

Mounts the lower spray arm assembly to the pump housing in your dishwasher. Replace if cracked, broken, or worn to restore proper spray arm installation.

Fix poor spray coverage with this dishwasher jump-up nozzle. Replaces worn or clogged nozzles that cause uneven cleaning. Simple DIY repair.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.