Parts for Electrolux PCFG3080AFB: 04 - Body Parts

Secures internal components to the range cabinet or chassis. Replace this mounting bracket if the original is cracked, broken, or missing to restore alignment.

This replacement cover protects internal components and restores your appliance's finished appearance. It fits the factory location to keep parts shielded from debris and accidental contact. What it does

• Replaces a cracked, broken or missing cover to stop exposed components and reduce risk of damage
• Helps prevent debris and moisture from entering internal areas that can cause malfunctions
• Eliminates rattles or vibration caused by a loose or damaged housing piece
• Restores a clean, finished look to the appliance exterior

• Disconnect power to the appliance before starting any repair
• Basic hand tools such as a screwdriver may be required; keep fasteners from the original part for reuse if in good condition
• Handle part carefully to avoid scratching the finished surface during installation

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Rack assembly for electric wall ovens. Replaces cracked, bent, or missing oven racks. Installs inside the oven cavity to hold cookware during baking.

Replacement air fry tray for wall ovens. Holds food above the oven surface for even airflow and crisping. Replace if cracked, warped, or missing.

Replace your gas range door seal when you notice heat escaping or uneven cooking. This gasket creates an airtight seal around the oven door. Verify fit with your model number before ordering.

Replace your range's interior light assembly to restore oven cavity illumination. Install when bulb won't stay secure or socket is damaged. Verify fit with your model number.

Replacement bottom panel for your gas range. Installs underneath the unit to cover internal components. Order if your current panel is damaged or missing.

Oven not heating to the right temperature? Replace the temperature sensor probe to restore accurate heat regulation and consistent baking results.

Range won't turn on or power cuts out intermittently? This power cord restores safe electrical connection from outlet to your gas range. Easy install.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Fix sparks, tripped breakers, or burnt connections at your range's power cord junction. Terminal block replacement takes about 5-10 minutes with basic tools.

Pin component for electric and gas ranges. Installs in assembly connections. Replace if broken, bent, missing, or worn to restore proper fit and alignment.

This replacement evaporator fan blade helps circulate cold air inside the freezer or refrigerator compartment to maintain even temperatures and proper cooling performance. A direct-fit replacement when the existing blade is cracked, warped, or missing. What it does:

• Moves air across the evaporator to promote even cooling and frost prevention
• Restores proper airflow when a damaged blade causes noise or reduced cooling
• Helps reduce hot or warm spots inside the compartment
• Quiet, balanced operation when installed correctly

• One replacement evaporator fan blade

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing interior panels in the freezer/refrigerator compartment
• Inspect the fan motor shaft and mounting for damage before installing the new blade

This is a mounting nut used to secure the fan blade to the motor shaft inside a range or oven. It keeps the convection or cooling fan firmly attached so it spins properly during operation. Replace this nut if the fan wobbles, rattles, or has come loose from the motor shaft.

Anti-tip bracket kit secures freestanding or slide-in ranges to prevent forward tipping. Includes mounting hardware for floor or wall installation.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.