Parts for Maytag MAH6500AWQ: 04 - Control Panel & Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Color: White

Replacement mounting screw for securing panels, brackets, and components. Needed when original fasteners are stripped, missing, or damaged during repair.

Replacement mounting screw for securing panels, brackets, and components in dryers, refrigerators, and washers. Needed when screws are lost or stripped.

Located in the detergent dispenser drawer, this small cup creates suction to draw liquid detergent into the wash cycle. Replace it if detergent remains in the dispenser after cycles or if dispensing becomes inconsistent.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a rubber hose that connects to the tub fill nozzle inside the washing machine, directing water into the wash tub during the fill cycle. It ensures water flows properly from the inlet valve to the tub. Replace this hose if you notice water leaking inside the cabinet, reduced water flow into the tub, or if the hose has become cracked or brittle.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

New seals come with this valve.

Screw: 8-16 x 3/8 inch.

This control board is made for use with washing machines. The basic purpose of the component is to regulate the speed at which the washer spins during a cycle. It determines and executes all of the essential functions of the appliance. It can control the drain pump, drive motor, fill valves, and other parts. If this part is damaged or malfunctioning, the washer may have trouble draining, spinning, filling, or starting.If this part is damaged, it will need to be replaced to continue using the washing machine. Unplug the power cord from the wall and then take the control knob from the front of the console panel. Pull the washer forward and remove the screws from the top of the back panel. Disconnect the mounting clips and take off the air hose. Remove the mounting screws and remove the control board. Document the placement of wires before disconnecting them. Reassemble in the opposite way and plug in the washer before use.This control board is made to be compatible with washing machines by Maytag. It is sold on an individual basis and directly sourced from the manufacturer. This is a genuine OEM replacement part.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.