Parts for Maytag GB2225PEKW12: 04 - Refrigerator Door Parts

This replacement dairy door restores the flip-up cover for the small butter/dairy bin on your refrigerator door. Replace a cracked or missing cover to keep contents contained and your door storage tidy.

• Covers the butter/dairy compartment on the fresh food door
• Flips up for access and down to help secure items
• Helps prevent small items from sliding out of the bin
• Replaces a cracked, broken, loose, or missing cover

• Remove the dairy bin for easier access and alignment
• Align hinge tabs with the bin pivots and press gently until it snaps in
• Avoid forcing cold plastic; let parts warm to room temperature
• If working near electrical components, disconnect power and wear cut-resistant gloves

Replace a cracked or missing dairy tray on your refrigerator door. This door bin restores a dedicated spot for butter and small items so they stay organized and easy to reach while maintaining a secure fit on the door.

• Mounts on the refrigerator door as the dairy compartment tray
• Holds butter, cheese, and other small items securely
• Restores proper fit when the original tray is cracked, warped, or missing
• Common symptoms: broken tabs, tray falls off, loose/wobbly fit, items spilling when the door opens

• Open the door, lift the old tray straight up and out; align the new tray with the door slots and lower until fully seated
• Handle plastic parts gently and avoid forcing; allow parts to warm to room temperature to reduce risk of cracking
• Confirm both sides are fully engaged before loading items

This medium refrigerator door bin restores secure storage on the fresh food door. Replace a cracked or missing bin to keep bottles and condiments upright and accessible; it snaps into the door liner for a snug, factory-style fit.

• Mounts to the refrigerator door to hold everyday items securely
• Helps keep bottles and jars upright and organized
• Replaces bins that are cracked, warped, or missing
• Addresses issues like loose fit, broken tabs, or items falling when the door opens

• Remove contents and lift out the damaged bin
• Align the new bin's tabs with the door liner slots and press down until fully seated
• Verify a secure fit before loading items
• If removing additional door components for access, disconnect power for safety

The Gasket-FIP  is an OEM part for Whirlpool refrigerators, ensures an airtight seal around the door, preventing cold air from escaping and warm air from entering. This component contributes to the refrigerator's energy efficiency and cooling effectiveness, maintaining the optimal internal temperature to keep your food fresh longer. 

Causes of a bad Gasket-FIP can range from normal wear and tear, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures.  

Symptoms of a bad Gasket-FIP include:

• Noticeable gaps between the gasket and the refrigerator door or frame
• Condensation or frost buildup near the door edges
• The refrigerator working harder to maintain its internal temperature, potentially leading to increased energy bills
• The door not closing as smoothly or firmly as it should

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replace a worn or broken door handle with this factory-style assembly. It restores a secure, comfortable grip so you can open and close your refrigerator or freezer smoothly while keeping the appliance's look clean and consistent. What it does:

• Provides a sturdy handhold to open and close the appliance door
• Restores appearance when the original handle is scuffed, cracked, or discolored
• Addresses a loose or wobbly handle that won't stay secure
• Replaces a missing handle to make the door easy to use again

• 1 white door handle assembly

• Disconnect power before servicing and protect nearby surfaces with low-tack tape
• Align the handle with mounting points; start all fasteners by hand to avoid cross-threading
• Reuse existing brackets/fasteners as applicable; tighten screws evenly—do not overtighten
• Verify door opens/closes smoothly and the gasket seals properly after installation

This door hinge bushing restores smooth, stable movement at the refrigerator door pivot. It sleeves the hinge pin to reduce friction and wear, helping the door stay aligned so it closes cleanly and maintains a proper seal.

• Seats in the door hinge to guide the hinge pin and reduce friction
• Helps maintain door alignment and consistent gasket contact
• Replaces a worn, cracked, or missing bushing that can cause noise or binding
• Typical symptoms: squeaking or grinding at the hinge, door sagging/misalignment, door hard to open or close, or not closing flush

• Disconnect power; clear and support the door to prevent strain
• Remove hinge cover and fasteners; lift the door off the hinge pin as needed
• Remove the old bushing from the hinge area and press the new bushing fully into place, matching original orientation
• Reinstall hardware; adjust hinges/level as needed

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This white door stop limits how far the door swings open, helping protect hinges and nearby surfaces. Replace a worn or missing stop to restore the intended opening range and smooth, controlled door movement.

• Limits door swing to prevent overextension and impact
• Helps protect door hinges and surrounding cabinetry
• Restores proper opening range when the original stop is cracked or missing
• Common signs: door opens too wide, door hits adjacent surfaces, visible broken/missing stop

• Disconnect power and clear items from the door before service
• Support the door to prevent strain on the hinges
• Remove hinge cover and fasteners as needed, swap the stop, and reassemble
• Open and close the door to verify proper swing and gasket seal