Parts for Electrolux FFUE2022AWM: 04 - System Parts

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Refrigerator not cooling properly or running constantly? This condenser coil assembly removes heat from refrigerant to restore efficient cooling performance.

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Fix a refrigerator that won't cool or runs constantly with this inverter compressor drive module. Controls variable-speed operation for efficient cooling.

This wiring harness routes power and signals between appliance components to restore reliable electrical connections and proper control operation. It replaces a worn or damaged connector assembly to help stop intermittent power or control failures. What it does

• Provides secure electrical connections between control, switches, and components
• Restores continuity when original wires or terminals are damaged or corroded
• Stops intermittent operation, control communication errors, or no-power symptoms
• Helps eliminate arcing or poor contact that can cause heat or burning smells

• One wiring harness assembly

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Confirm wire routing and connector orientation before disconnecting; photograph for reference
• Avoid pinching or stressing wires; secure harness with existing clips or ties

Fixes poor cooling and warm temps caused by moisture in the sealed system. This filter-drier protects the compressor during refrigerant repairs.

Freezer not cooling or running constantly? This evaporator coil assembly circulates refrigerant to absorb heat and restore proper cold temperatures.

Fix frost buildup and cooling issues with this defrost heater. Restores proper defrost cycles and eliminates excessive ice in your refrigerator or freezer.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

This assembly includes a defrost bi-metal thermostat and the accompanying wire harness for a freezer. The thermostat monitors evaporator coil temperature and signals the defrost system to turn on or off, preventing excessive frost buildup. Replace this assembly if the freezer is accumulating heavy frost on the back wall, running too warm, or if the defrost cycle is not activating properly.

Fix poor cooling or overheating issues. This condenser fan shroud assembly directs airflow across the condenser to restore cooling efficiency.

Water pooling under your refrigerator? This drip pan collects defrost water and condensation to prevent leaks. Direct-fit replacement part. Easy DIY.

If your oven won't heat, displays errors, or buttons don't respond, this control board and housing assembly restores temperature control and user interface.

This baffle directs cold air inside the refrigerator to help maintain even temperatures and proper airflow. Replacing a damaged or missing baffle restores intended air circulation and helps performance. What it does

• Channels and directs airflow between compartments for more consistent cooling.
• Helps prevent warm spots caused by blocked or misdirected air.
• Reduces stress on the cooling system by restoring designed airflow paths.
• Commonly replaced when cracked, broken, or missing, or when airflow is visibly obstructed.

• Unplug the appliance or disconnect power before starting any work.
• Remove food, shelves, and drawers as needed for access; handle components gently to avoid damage.
• Inspect mounting points and gaskets; replace any damaged fasteners or seals.
• Refer to OEM instructions for model-specific removal/replacement steps.

This cover drain jumper is a molded drain-channel cover that helps route defrost and condensate water into the refrigerator drain system, preventing water from pooling inside the cabinet and reducing ice buildup. What it does:

• Guides defrost and condensate water into the drain channel so it flows to the drain pan
• Helps prevent water from pooling at the back or bottom of the fresh-food compartment
• Reduces the chance of ice forming around the evaporator or in the drain path
• Fits into the drain housing to maintain proper condensate flow

• Disconnect power to the appliance before beginning any service.
• Remove shelves/panels that obstruct access to the drain area; handle plastic parts gently to avoid breakage.
• Make sure the drain channel is clear of debris and ice before installing the cover for best results.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.