Parts for Electrolux FRAE2024AW4: 04 - System Parts

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

This evaporator drain tube channels defrost and condensation water from the freezer/refrigerator evaporator to the drain pan, helping prevent water buildup and pooling inside the cabinet. What it does

• Guides defrost and condensation water out of the evaporator area to the drain pan.
• Helps prevent water pooling under shelves or in the fresh-food compartment.
• Commonly replaced when cracked, clogged, or detached causes leaks or excess moisture.
• Works with the evaporator, drain funnel, and drain pan as part of the cabinet drainage system.

• One evaporator drain tube.

• Disconnect power before servicing to avoid electrical shock.
• Inspect surrounding drain funnel and pan for clogs or damage and clear debris before installing.
• Ensure tube is seated and routed per service manual to maintain proper drain flow and avoid kinks.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Fixes poor cooling and warm temps caused by moisture in the sealed system. This filter-drier protects the compressor during refrigerant repairs.

Fix frost buildup and cooling issues with this defrost heater. Restores proper defrost cycles and eliminates excessive ice in your refrigerator or freezer.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Fix a refrigerator that won't cool or runs constantly with this compressor starter relay. Essential sealed system component for reliable operation.

This assembly includes a defrost bi-metal thermostat and the accompanying wire harness for a freezer. The thermostat monitors evaporator coil temperature and signals the defrost system to turn on or off, preventing excessive frost buildup. Replace this assembly if the freezer is accumulating heavy frost on the back wall, running too warm, or if the defrost cycle is not activating properly.

The Capacitor is an OEM part for Frigidaire refrigerators. It is part of the refrigerator's electrical system, responsible for providing a boost of power to start the compressor.

A bad capacitor can be caused by electrical issues, component failure, or damage. When the capacitor becomes faulty, it can result in issues such as the compressor not starting, inadequate cooling, or the refrigerator not running at all.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• Unusual noises from the compressor 
• Compressor turning on and off rapidly
• The refrigerator not running at all

Replace your faulty capacitor with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Condenser Fan Motor is an OEM part for Frigidaire refrigerators. Located behind the rear refrigerator wall and grille, the condenser fan motor works to dissipate heat from within the refrigerator system. 

Symptoms of a bad condenser fan motor include:

• Refrigerator failing to adequately cool or ice up  
• Increased humming and vibrations
• Elevated compressor run times 
• Warm air discharge from rear grill

Causes of a bad condenser fan motor can include winding failures, bearing seizing, or obstructed fan blades no longer spinning freely.

This genuine OEM Frigidaire motor is compatible with some Electrolux, KitchenAid and Danby French door refrigerator models as well.

Fix a refrigerator that won't cool or runs constantly with this compressor kit. Includes the compressor and electrical components needed to restore cooling.

This main control board is the oven/range electronic control that manages cooking functions, timing and user interface. Replacing a faulty board restores responsive controls and reliable operation for affected functions. What it does:

• Controls oven and cooktop functions, timers, and cycle sequencing
• Manages the user interface and display signals
• Can resolve unresponsive or intermittently working controls
• Stop error-code symptoms tied to a failed electronic control

• Disconnect power to the appliance before starting work to avoid shock or damage
• Handle the board by edges and avoid static discharge; use ESD precautions
• Follow factory wiring diagrams and mounting locations exactly

This cover drain jumper is a molded drain-channel cover that helps route defrost and condensate water into the refrigerator drain system, preventing water from pooling inside the cabinet and reducing ice buildup. What it does:

• Guides defrost and condensate water into the drain channel so it flows to the drain pan
• Helps prevent water from pooling at the back or bottom of the fresh-food compartment
• Reduces the chance of ice forming around the evaporator or in the drain path
• Fits into the drain housing to maintain proper condensate flow

• Disconnect power to the appliance before beginning any service.
• Remove shelves/panels that obstruct access to the drain area; handle plastic parts gently to avoid breakage.
• Make sure the drain channel is clear of debris and ice before installing the cover for best results.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.