Parts for Maytag PBB1951HEB: 06 - Freezer Door Parts

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This vent plug seals an unused appliance vent opening to keep out debris and improve appearance. A simple OEM-fit replacement that restores a clean, finished look to the appliance exterior. What it does

• Covers and seals a vent opening to prevent dust, lint, and pests from entering the cabinet or vent cavity.
• Restores the appliance's finished appearance where a vent opening is exposed or a plug is missing.
• Helps maintain proper airflow paths by closing unused ports and reducing drafts.
• Fits the original mounting location for a secure, low-profile fit.

• One black vent plug.

• High-level push-in replacement; no special tools typically required.
• Disconnect power to the appliance before any service when accessing internal areas.
• Inspect surrounding trim or grille for clips or screws; remove carefully to access the vent opening.
• If plug does not seat fully, verify the correct OEM location and orientation before forcing.

This freezer door retainer is a small mounting clip that secures the freezer door/inner panel and helps keep the door aligned for a proper seal. Replaces a broken or worn retainer to restore reliable door positioning and reduce air leaks. What it does:

• Secures the freezer door or inner door panel to the cabinet or hinge assembly
• Helps maintain proper door alignment for an effective freezer seal
• Common fix when the door drops, pulls away, or creates a visible gap
• Prevents unnecessary cold air loss from a misaligned or loose door

• One freezer door retainer

• Disconnect power before beginning repairs and follow manufacturer safety instructions
• Access may require removing the freezer door or inner panel and existing fasteners
• Inspect surrounding hinge and mounting hardware for wear and replace if needed

A direct-replacement Plug B push button for the appliance control panel that restores tactile operation for the associated function. Ideal for replacing cracked, worn, or missing buttons so controls respond and look right again. What it does:

• Replaces the Plug B push button on the appliance control/interface so the linked control works properly.
• Provides the tactile surface users press to select a setting, cycle, or function.
• Common symptoms this part can fix: button is cracked, sticking, missing, or no longer actuating the switch.
• Cosmetic refresh when a button is faded or damaged.

• Always disconnect power to the appliance before servicing to avoid shock or injury.
• Replacement typically requires removing the control panel or trim; keep screws and small parts organized.
• Handle the button and panel clips gently to avoid breaking plastic retainers.

This nonmetal shim spaces and cushions appliance components to improve alignment and reduce rubbing or vibration. Use it to replace a missing or worn shim and help restore quieter, smoother operation. What it does:

• Provides a thin, durable spacer to correct component alignment and clearances
• Cushions parts to reduce rubbing, squeaks, and vibration during operation
• Helps stabilize panels, housings, or assemblies that sit unevenly
• Can prevent premature wear where metal parts contact one another

• Disconnect power (and water, if applicable) before accessing internal components.
• Verify exact shim location against the appliance diagram; position shim between mating surfaces as shown.
• Use basic hand tools as needed; ensure parts are reassembled and fasteners are secure before testing.

Restore a solid, comfortable grip on your freezer door with this black Freezer Door Handle. It replaces a damaged or worn handle to bring back dependable daily use and a clean, factory look.

• Provides a sturdy handhold for opening and closing the freezer door
• Direct replacement for a cracked, broken, loose, or missing handle
• Refreshes the appliance's appearance if the old handle is scuffed or discolored
• Installs on the existing mounting points for your model

• Unplug the appliance and secure the door before service.
• Access and loosen the handle's set screws or mounting screws, then remove the old handle.
• Position the new handle; transfer and tighten existing fasteners evenly—do not overtighten.
• Verify smooth door operation and alignment after installation.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This Bottom Hinge Pin supports the refrigerator door at the lower hinge, providing a smooth, stable pivot. Replace a worn or bent pin to restore proper door alignment, closing action, and gasket sealing.

• Serves as the pivot point for the door on the bottom hinge bracket
• Helps maintain alignment so the door gasket seals correctly
• Wear/failure symptoms can include door sagging, wobble at the hinge, squeaks or grinding, and poor self-closing
• Replacing a damaged pin can reduce hinge play and improve door operation

• Disconnect power; turn off water supply if working near a dispenser line
• Remove items from the door and support the door to prevent strain on hinges
• Detach bottom hinge fasteners, lift door off, replace the pin, and reassemble
• Adjust hinges as needed