Parts for Maytag WU400: 06 - Front View-Lower Half-Panel Removed Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Size: 8-32 x 1/4 inch.

This part has been discontinued by the manufacturer and is no longer available.

Hose assembly for portable dishwashers. Connects your unit to the sink faucet for water supply. Replace if cracked, leaking, or stripped threads.

Specs: 10 - 16 x .375

Size: 10-32

A replacement mounting screw used to secure appliance panels and components. This genuine-style fastener restores proper fit and prevents loose or rattling parts for many Whirlpool appliances. What it does:

• Fastens panels, trim, brackets, or components to the appliance frame
• Restores secure attachment when original screw is missing, stripped, or damaged
• Helps eliminate rattling, vibration noise, and loose-fitting parts
• Matches OEM fit and function when the correct part number is used

• Disconnect power (and water, if applicable) before servicing the appliance.
• Use the correct screwdriver or driver bit to avoid stripping the head; do not overtighten.
• Replace only with the exact part number to ensure correct fit; keep removed hardware organized for reassembly.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Secures the power cord where it enters the cabinet, protecting the jacket and preventing pull on internal connections. Replace if cracked, broken, or missing.

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.

Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.