Parts for Amana ABB1922FEB: 08 - Refrigerator Door Parts

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

Replace a worn door gasket to restore an airtight seal, keep cold air in, reduce frost, and improve efficiency. Verify fit with your model number.

This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.

• Fastens panels, brackets, covers, and internal hardware to the cabinet or frame
• Helps prevent loosening, rattling, or misalignment during appliance operation
• Replace if the head is rounded, threads are stripped, or the screw is missing
• Useful after service when an original fastener is lost or damaged

• Disconnect power and shut off gas/water before starting
• Use the correct nut driver or socket for the hex head to avoid rounding
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening

Mounts at the upper corner of the cabinet to support and pivot the refrigerator door. Replace if bent, cracked, or missing to restore door alignment.

Plastic cover that conceals the top hinge assembly on your refrigerator door. Replace if cracked, broken, or missing to restore a clean appearance.

This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.

• Fastens panels, brackets, covers, and internal hardware to the cabinet or frame
• Helps prevent loosening, rattling, or misalignment during appliance operation
• Replace if the head is rounded, threads are stripped, or the screw is missing
• Useful after service when an original fastener is lost or damaged

• Disconnect power and shut off gas/water before starting
• Use the correct nut driver or socket for the hex head to avoid rounding
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening

Color: Black

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Black plastic plug that seals unused refrigerator vent openings. Replace if yours is cracked, broken, missing, or damaged to keep out debris.

Replace a cracked, broken, or missing dairy tray on your refrigerator door. This bin installs on the door to organize butter and small items in one spot.

Replacement flip-up cover for the butter/dairy bin on your refrigerator door. Replaces cracked, broken, or missing covers to keep contents secure.

Replacement door bar rail for refrigerator door shelves. Snaps onto shelf edge to create a secure barrier. Order when original is cracked or broken.

Medium door bin for refrigerator fresh food compartment. Replaces cracked, broken, or missing door shelf. Snaps into door rails for secure storage.

Secures and supports your refrigerator door for smooth pivoting and proper alignment. Replace if door sags, won't close fully, or hinge is damaged.

Metal pivot pin for the center hinge on refrigerator doors. Restores smooth door swing and proper alignment when original pin is worn or broken.

Small door bin mounts on the inner refrigerator door panel for organized storage. Replaces cracked, loose, or missing bins to restore usable space.

Mounting screw for refrigerator assembly. Secures components and panels in place. Replace if screw is stripped, missing, or no longer holding tight.

Black hi-torque screw secures refrigerator panels, brackets, and door handles. Replace worn, stripped, or missing fasteners for solid connections.

This is a small plastic plug or button cap that fills an unused hole on the refrigerator door panel. It provides a finished appearance and prevents moisture or debris from entering the door. Replace this piece if it is missing, cracked, or has fallen out, leaving an exposed hole in the door surface.

This decorative identification nameplate replaces a worn, damaged, or missing Amana Plus front badge to restore appliance appearance and legibility of branding/details. It's a simple cosmetic replacement that keeps the exterior looking finished. What it does:

• Replaces a faded, scratched, or missing Amana Plus nameplate on the appliance exterior
• Restores readable product branding and identification on the front panel
• Improves overall appearance after cosmetic wear or accidental damage
• Helps owners quickly identify the model area without guessing

• Turn off and unplug the appliance before starting any work near electrical components.
• Clean and dry the mounting area so the nameplate adheres or seats properly.
• Remove any remaining adhesive or clips from the old plate before installing the new one.
• Align carefully and press firmly; if fasteners are present on your model, retain and reuse as needed.

Black plastic cam that the refrigerator door rides on to open and close smoothly. Replace if cracked, worn, or broken causing door misalignment issues.