Parts for Electrolux GRFC2353AD7: 09 - Ice Maker Parts

This replacement refrigeration tube routes water between the dispenser/valve and internal components to restore reliable water flow and drainage. It's a simple, low-cost part that helps stop leaks and restore proper water delivery. What it does

• Channels water from the inlet valve to internal lines or dispenser components
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow
• Helps stop visible drips under or inside the refrigerator when the original tube fails
• Works as a direct-fit service part when the OEM tube is damaged

• One replacement tube as shown

• Disconnect power and shut off the water supply before beginning any work
• Inspect fittings and clamps; replace any damaged fasteners to prevent leaks
• Route the tube following original path; avoid sharp bends and pinch points

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Not making ice or producing small/hollow cubes? This refrigerator icemaker assembly automatically produces and dispenses ice. Moderate DIY repair.

Ice dispenser not working or making grinding noises? A worn auger drive bar often causes dispensing failures. Moderate DIY fix with video guidance.

Door won't seal or warm fridge? This refrigerator door gasket restores airtight closure to maintain temperature and reduce energy loss. Direct fit.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

Fix intermittent power issues or electrical failures with this wire harness connector. Restores secure plug-in connections in refrigerator circuits.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Replacement mounting screw for refrigerator panels, brackets, and trim. Secures loose or missing fasteners to stop rattles and keep components aligned.

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

No water to ice maker or dispenser? This dual-solenoid water valve controls flow to both systems. Fixes leaks and restores normal water delivery.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Mounting screw for refrigerator panels, handles, and internal components. Replace stripped, corroded, or missing screws to secure assemblies properly.

Fix water leaks or low ice production with this refrigerator water tube assembly. Replaces cracked tubing affecting icemaker and dispenser flow. Quick repair.

Small retainer clip that secures components, panels, tubes, or wires in place inside your refrigerator. Replace when worn, broken, or missing to restore fit.

Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

The Thermistor Kit is an OEM part for Frigidaire refrigerators. Consisting of a thermistor temperature sensor and mounting bracket, this kit plays a key role in refrigeration system operation. Strategically positioned inside the unit, the sensor continually monitors interior temperatures to maintain proper cooling levels throughout all compartments. 

Symptoms of a bad thermistor kit include:

• Fluctuating or uncontrollable temperatures within sections of the fridge
• The condenser or evaporator fans running excessively long periods  
• Ice buildup inside compartments disrupting temperature regulation

Causes can involve thermistor degradation over time losing sensitivity and providing inaccurate reads to system computers.  

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.