Parts for Electrolux GRMS2773AF01: 09 - Ice Maker System Parts

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

Replacement drive motor that powers an appliance's rotating components, restoring normal operation and reliable movement. Use this motor to address rotation failures and abnormal noises so the unit can run as intended. What it does

• Turns the appliance's rotating assemblies to enable normal operation.
• Helps when the appliance won't rotate, tumble or start turning even though power is present.
• Restores consistent speed and torque for proper cycle performance.

• Disconnect power before attempting any service to avoid shock or injury.
• Verify alignment and mounting orientation; secure all fasteners to manufacturer torque where specified.
• Inspect wiring harness, connector pins and any grommets for damage; replace damaged components as needed.

This wiring harness connects electrical components and control circuits to restore reliable power and signal paths in the appliance. It replaces damaged or worn wiring to help eliminate intermittent operation and poor connections. What it does

• Transfers power and control signals between the control board and components to enable normal operation.
• Replaces frayed, burnt, or broken wires and damaged connector ends that cause intermittent or no power.
• Helps address symptoms such as intermittent cycles, components that do not run, or error codes caused by poor connections.
• Maintains secure, keyed connections to prevent miswiring and ensure correct polarity where applicable.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Compare the harness to the original, match connector types and pin counts, and route it following original wire paths.
• Secure with existing clips or fasteners; avoid contact with sharp edges, moving parts, or heat sources.

Fix intermittent power issues or electrical failures with this wire harness connector. Restores secure plug-in connections in refrigerator circuits.

This complete evaporator assembly circulates refrigerant and supports proper airflow in the freezer compartment to help maintain consistent cooling and reduce frost buildup. It replaces the evaporator coil and mounting components as an assembly. What it does:

• Enables refrigerant to absorb heat from the freezer, a core part of the cooling cycle
• Restores proper cold temperatures when a damaged or leaking evaporator causes poor cooling
• Helps reduce excessive frost or ice buildup when paired with a working defrost system
• Works with the evaporator fan and defrost components to maintain consistent freezer performance

• High-level replacement: may require accessing the freezer interior and removing liners or panels
• Handle refrigerant components with care; manage refrigerant service
• Disconnect power before starting work to avoid electrical shock or injury
• Inspect and test related components (evaporator fan, defrost heater/thermostat) for best results

The Thermistor Kit is an OEM part for Frigidaire refrigerators. Consisting of a thermistor temperature sensor and mounting bracket, this kit plays a key role in refrigeration system operation. Strategically positioned inside the unit, the sensor continually monitors interior temperatures to maintain proper cooling levels throughout all compartments. 

Symptoms of a bad thermistor kit include:

• Fluctuating or uncontrollable temperatures within sections of the fridge
• The condenser or evaporator fans running excessively long periods  
• Ice buildup inside compartments disrupting temperature regulation

Causes can involve thermistor degradation over time losing sensitivity and providing inaccurate reads to system computers.  

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Ice dispenser not working or making grinding noises? A worn auger drive bar often causes dispensing failures. Moderate DIY fix with video guidance.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Replacement mounting screw for refrigerators. Secures panels, brackets, and trim components. Replace if missing, stripped, or damaged to restore fit.