Admiral Cooktop Parts

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

This thermostat knob is the front control dial that lets you set an appliance's temperature and restore easy, accurate temperature selection. It replaces a worn, cracked, or hard-to-turn knob so controls respond like new. What it does

• Provides a secure grip for turning the thermostat or temperature control
• Aligns with the control shaft to show and select temperature settings
• Fixes symptoms such as a loose, cracked, or stuck knob and difficulty changing temperature
• Restores tactile feedback and clear position indication when selecting settings

• Disconnect power or unplug the appliance and allow it to cool before servicing.
• Most knobs simply pull straight off the control shaft; align the indicator and push fully on until seated.
• If the knob uses a retaining clip or keyed shaft, match orientation before pressing on.

This screw is a factory-style mounting fastener used to secure appliance panels and components. It replaces worn, stripped, or missing screws to restore proper fit and reduce rattling. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces damaged or corroded fasteners that can cause loose parts
• Helps maintain safe, stable operation of moving or load-bearing assemblies

• Turn off power and unplug the appliance before servicing
• Use the correct driver bit and match thread engagement to avoid stripping
• Tighten snugly but avoid over-torquing which can crack plastic or strip threads
• Wear eye protection and keep small parts away from children and pets

Screw (bur) is a fastener that secures panels, brackets and small assemblies on select Whirlpool appliances. Replacing a missing or damaged screw restores proper fastening and helps reduce vibration, rattling and misalignment. What it does:

• Fastens panels, mounting brackets and small internal or external components to the appliance frame.
• Replacing a stripped or missing screw prevents loose parts and restores a secure fit.
• Symptoms of a failing screw include rattling, vibration, panels or trim that do not sit flush, or components that move during operation.
• Commonly used where a short machine screw or trim fastener is required for assembly.

• Disconnect power before beginning any service.
• Use the correct screwdriver or driver bit and install straight to avoid stripping the head or threads.
• Do not overtighten — snug until secure to prevent damage to threads or parts.
• Keep removed fasteners organized and replace any damaged screws with the exact OEM fastener.

This replacement thermostat knob restores reliable temperature control and a secure grip on your appliance's temperature selector. It makes turning the thermostat smooth and precise so you can set cooking or cooling levels confidently. What it does:

• Replaces a cracked, stripped, or missing thermostat knob for straightforward temperature adjustments
• Provides a firm, non-slip grip to improve control when changing settings
• Stops slipping or loose knob operation that prevents accurate temperature selection
• Matches OEM fit and rotation profile for consistent operation with the original control shaft

• Always unplug the appliance or shut off power before replacing control parts
• Most installations are push-on: pull the old knob straight off the control shaft and press the new knob firmly into place
• If the old knob is stuck, use a gentle rocking motion or a knob puller; avoid excessive force that could damage the control shaft

This band motor is the motor assembly that powers the appliance's moving band or drive link, restoring the mechanism that enables normal rotating or indexing motion. Use it to replace a worn or failed motor for smoother operation. What it does:

• Drives the appliance's band/drive link so the linked components can rotate or index as designed
• Restores motion when the original motor is noisy, weak, or no longer turns
• Helps stop skipping or intermittent movement caused by a failed motor
• Works as the direct replacement motor when the OEM part is specified

• One band motor assembly

• Disconnect power before starting any repair to avoid shock or injury
• Installation may require removing panels and fastening the motor to the band/drive; keep hardware for reassembly
• Verify alignment and secure belt or band tension per the appliance's service instructions

This replacement control knob restores user control and clear settings for range or oven functions, making it easy to select temperatures or cooking modes. It provides a direct-fit user interface for worn, broken, or faded knobs. What it does:

• Replaces a damaged, cracked, or missing control knob so you can turn settings smoothly
• Restores a visible indicator/pointer for accurate temperature or function selection
• Eliminates looseness or slipping that prevents setting changes
• Provides a direct-fit manual interface—no electronic repair required

• Disconnect power to the appliance before servicing to avoid electric shock
• Most knobs pull straight off the valve or shaft; align the splines/pointer and push firmly until seated
• If knob is stuck, gently pry with a flat tool while protecting the surrounding finish

This snap-in bushing provides a low-profile bearing surface to support rotating shafts and reduce wear and noise in appliance assemblies. It restores smooth operation where the original bushing is worn or damaged. What it does:

• Provides a replaceable bearing/sleeve for rotating shafts and posts
• Reduces friction and wear on housing and moving parts
• Helps eliminate rubbing, grinding, or rattling noises during operation
• Maintains correct shaft alignment for smooth rotation

• One snap-in bushing

• Disconnect power before servicing and follow all safety instructions
• Access may require removing panels or covers; inspect surrounding parts for wear
• Press or snap the bushing squarely into the housing until fully seated; avoid deforming it
• Replace any damaged retainers or seals and test operation after reassembly

This infinite switch controls heat output to an electric range surface burner, restoring variable temperature control for cooking. Replacing a worn or faulty burner control brings back smooth, stepless power adjustment at the cooktop. What it does:

• Regulates electrical power to a surface/top burner so you can set low-to-high heat levels.
• Re-establishes variable temperature control when a burner is stuck high, stuck low, or won't heat.
• Replaces a failing rotary control that clicks, won't change settings, or loses continuity.
• Works with the cooktop wiring and mounting used by the original burner control.

• Disconnect power at the breaker before starting any repair to avoid electric shock.
• Verify the replacement matches the old switch's terminals and mounting before installation.
• Reconnect wiring securely and test the burner operation after restoring power.

This wing nut is a hand-tightening fastener used to secure small appliance components for easy tool-free adjustment or removal. It offers a simple replacement when the original nut is lost, stripped, or broken. What it does:

• Secures panels, brackets, or components that require occasional removal or adjustment
• Allows tool-free tightening and loosening with built-in wings for finger grip
• Restores proper fit where a missing or damaged nut causes rattling, looseness, or instability
• Designed for repeated hand-operation without specialized tools

• Disconnect power to the appliance before performing any work to avoid shock or injury
• Thread by hand until snug; avoid overtightening to prevent stripping threads or cracking surrounding parts
• Inspect mating threads and replace if damaged to ensure secure fastening
• Use appropriate size and thread type—do not force a mismatched nut onto the stud

This is a genuine replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Simple, low-cost fastener that helps keep parts aligned and stable. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Restores secure connections that can cause buzzing, rattling, or loose trim
• Replaces missing or stripped hardware to prevent further movement or wear
• Works where the original OEM screw was specified for fit and compatibility

• Disconnect power before working on electrical appliances to avoid shock
• Use the correct size driver to avoid stripping the head
• Install by hand initially to ensure proper threading, then snug—do not overtighten
• Retain removed hardware and compare to the new screw for correct fit before final assembly