Admiral Range Parts

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

Replace your cracked, stripped, or missing gas cooktop burner control knob. Mounts on the valve stem to restore smooth operation and control heat levels.

If your cooktop burner won't heat, stays on one setting, or heats erratically, this control switch regulates power to restore proper temperature selection.

Replace a cracked, worn, or broken burner grate on your gas range or cooktop. This grate supports cookware over the burner for stable, level cooking.

Replacement control knob for cooktop surface switches. Fits on the switch shaft for secure grip when adjusting burner settings. Needed when original is cracked, faded, loose, or missing.

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

Square control knob for gas ranges. Replaces worn, cracked, or missing selector knobs to restore secure grip and clear setting selection. Easy DIY install.

Black control knob for gas range burner valves. Replaces cracked, broken, or missing knobs. Installs on the control panel. Sold individually.

Burner won't ignite or control knob is hard to turn? This top burner valve controls gas flow to surface burners. Moderate DIY repair with basic tools.

Cable retainer for electric ranges. Secures and organizes internal wiring. Replace if cracked, broken, or missing to properly route cables inside your range.

Range retainer clip secures components in place during operation. Replace if loose, broken, or missing to prevent rattling and ensure proper assembly.

Black control knob fits over the burner valve stem on your range or cooktop. Replaces worn, cracked, or missing knobs to restore heat adjustment.

White control knob for gas range burner or oven valve adjustment. Replaces worn, cracked, or missing knobs. Restores secure grip and precise control.

This shaft-bit generator is a replacement drive shaft component that transfers motor rotation to the appliance's moving assemblies, restoring proper mechanical motion and reducing noise from damaged or worn shaft parts. What it does:

• Transfers rotary motion from the motor to the driven components for normal operation
• Helps maintain alignment and smooth rotation of connected parts
• Worn or broken units can cause grinding, rattling, or loss of movement
• Replacing a failed shaft can stop intermittent operation and restore reliable performance

• High-level replacement only: remove power before accessing internal assemblies
• Follow appliance-specific disassembly steps; secure panels and wiring before removing the old shaft
• Inspect adjacent bearings, seals, and mounting hardware; replace any damaged items