Need Help?
Call
Refrigerator freezing food or not cooling? This temperature control thermostat regulates cooling cycles. Common DIY fix when temps won't stay consistent.
Ordered a cold thermostat switch and installed it. Read more
Black freezer door handle for bottom-mount refrigerators. Replaces cracked, broken, or worn handles. Mounts to freezer door with two screws.
Ordered a new handle and replaced it Read more
Right-side crisper cover support mounts to the inner wall and holds up the crisper cover and glass. Replace if cracked, broken, or missing to restore level.
White plastic bushing that sleeves the hinge pin where your refrigerator door pivots. Replace when cracked, worn, or missing to restore smooth door swing.
Purchased new hinge bushing, door closer, and hinge pin. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.
I SAW THE VIDEO AND WAS SO EASY THAT MY CHILDREN COULD DO IT Read more
Mounts at the upper corner of the cabinet to support and pivot the refrigerator door. Replace if bent, cracked, or missing to restore door alignment.
A friends family had left her refrigerator out on a porch while they were remodeling the house she was supposed to move into. A wind storm blew the refrigerator off the porch and tore the door off. It wasn't dented at all, but when her son pu the door back on, it wouldn't seal. She asked for some help fixing it. I ordered replacement parts for the upper and lower hinge. The parts arrived quickly. I unscrewed the top hinge which was slightly bent. Set the door on its side and replaced the bent... Read more
Replacement center hinge for refrigerator doors. Mounts between upper and lower doors to provide support and alignment. Replace if cracked or worn.
Protective thimble bushing that reinforces the hinge pin mounting hole in your freezer door liner. Replace if worn, cracked, or missing to stabilize hardware.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Fresh food section. Color: clear. Measures about 3 inches in diameter.
Replaced the temp controller Read more
Freezer not maintaining proper temperature or running too cold? This temperature control regulates freezing conditions and restores accurate adjustment.
New temp. control Read more
Replace your cracked, loose, or missing refrigerator door handle with this face-mount assembly. Restores a solid grip for smooth opening and closing.
Replaced Handle. Read more
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Seals the FIP assembly to prevent air and moisture leaks, maintaining proper temperature. Replace if you notice condensation, frost buildup, or temperature fluctuations. Verify fit with your model number before ordering.
As seen on your video, it was actually easier than shown, easy job, Thanks Wayne Russeell Read more
This is the outer cover that protects the electrical terminal block on the back of a dryer. It shields the power cord connection point from accidental contact and helps prevent dust or debris from reaching the wiring terminals. Replace this cover if it is cracked, broken, or missing to ensure safe operation and protect the electrical connections.
Replaced broken coupling with new coupling Read more
Ice cubes jamming or hanging up in the ice maker? This stripper arm guides cubes off ejector fingers into the bin. Requires removing ice maker to install.
Removed icemaker and inserted the part Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.