Amana Wall Oven Parts

This pilot thermostat is the oven temperature control that senses heat and helps regulate burner operation for consistent cooking. It replaces a worn or faulty thermostat to restore accurate temperature response and reliable oven ignition. What it does:

• Senses oven temperature and signals the burner/pilot system to maintain set heat levels
• Helps the oven light and hold temperature when the pilot or main burner is used
• Commonly used when the oven won't heat, cycles excessively, or fails to maintain consistent temperature
• Works as the temperature-sensing control element in gas oven pilot systems

• One pilot thermostat

• Turn off power and shut off gas supply before starting any service
• Handle thermostat gently; avoid bending or stressing the sensing element or capillary tube
• Verify wiring connections match the old part; replace like-for-like

The Surface Element is an OEM component specifically designed for Whirlpool ranges and cooktops. It provides the heating source for cookware on the stove surface.

Causes of a bad element include deterioration of insulation material over time, carbonization or damage from pans slammed onto the element, or contact with moisture. 

Symptoms of a bad element include:

• Inability to heat cookware sufficiently 
• Uneven or incomplete heating of pans placed above
• Burn marks or discoloration visible on the element
• Crackling or popping noises heard from below pans

This part is also compatible with some Kenmore, Frigidaire, and select GE range models. Proper cooking performance and safety are maintained with an OEM surface element replacement when needed.

The Coil Surface Element is a 6-inch OEM part for Whirlpool ranges. It is responsible for radiating heat from its coils to cook food positioned above the stovetop grates. 

Symptoms of a faulty coil surface element include:

• Slow or uneven heating of pots and pans  
• Hot and cold spots on cooking surfaces
• Element coils glowing dimly or not at all
• Buzzing or crackling noises coming from below cookware

Causes can be mineral deposits coating the coils over time, physical damage like bending or breaks, or standard wear of heating filaments inside. 

This genuine OEM Whirlpool part is also compatible with the electric ranges of Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore brands.

The Inner Door Glass is an OEM part for Whirlpool microwaves. It forms the see-through window that allows for monitoring food as it cooks. The strengthened glass panel is designed to withstand prolonged exposure to steam and heat without issues.

Causes of bad inner door glass can include cracks or chips from accidental drops or impacts, or damage from cleaning chemicals or harsh scrubbing that compromise the glass integrity. 

Symptoms of a bad inner door glass include:

• Cracks or chips in the viewing surface
• Complete breakage leaving a hole in the door  
• Loose or improperly sealed glass panel
• Increased potential for leaks near door seals

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore microwaves.

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely. Replacing a worn hinge restores proper alignment and sealing to help the door latch correctly and operate as designed.

• Provides the pivot point and maintains door alignment
• Helps ensure smooth opening/closing and proper latching
• Supports a tight seal to prevent gaps, rattles, or temperature/moisture loss
• Typical failure signs: door sags, binds, squeaks, or won't stay closed/aligned

• Disconnect power before service; wear gloves to protect from sharp edges
• Support the door and control any spring tension; remove mounting hardware and the old hinge
• Install the new hinge in the same orientation; transfer any reusable hardware
• Adjust as needed

The Range Surface Element Wire Harness is an OEM part for Whirlpool ranges and cooktops. This harness routes power between the switches and surface heating elements.

Causes include continuous exposure to cooking heat, mechanical stress from opening/closing element covers, and standard wear over time.

Symptoms of a malfunctioning wire harness include:

• Inaccurate or inconsistent element temperature readings
• Elements failing to turn on or heating unevenly
• Error codes related to element malfunctions

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

Color: Stainless

The Surface Burner Orifice Holder is an OEM part specially designed for Whirlpool gas ranges and cooktops. This part holds and positions the burner orifice above the surface burner, facilitating the mixture of gas and air required for combustion. 

Symptoms of a bad orifice holder include:

• Yellow or incomplete burner flames  
• Flames not remaining centered on the burner surface
• Burners that will not light or stay lit
• Gas leaks detected around the burner area

This is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper gas ranges and cooktops. 

This orifice controls the flow of gas to a burner, helping produce the correct flame for safe, consistent cooking and baking. It replaces a worn or damaged gas metering jet to restore proper burner performance. What it does:

• Meter gas flow to a specific burner for correct flame size and heat output
• Helps maintain steady ignition and even cooking when functioning properly
• Commonly used when a burner shows a weak, uneven, or no flame
• Also replaces corroded or clogged jets that restrict gas flow

• Turn off the gas supply and power to the appliance before beginning work
• Use appropriate tools and avoid overtightening; match the replacement to the original part number
• Inspect for debris or corrosion and clean mating surfaces before installation

A surface ignitor that produces the spark needed to light gas burners on compatible ranges and cooktops. Replaces a worn or failed ignitor to restore reliable ignition and consistent burner lighting. What it does

• Creates the spark at the burner to ignite gas when the control is turned on.
• Commonly used when burners click but fail to light or when a specific burner never ignites.
• Works with the cooktop's ignition system to provide consistent, repeatable sparking.
• Fits into the burner assembly and connects to the appliance's existing wiring and mounting.

• One surface ignitor (quantity: 1)

• Disconnect power to the appliance and shut off the gas supply before starting any service.
• Handle the ignitor by the ceramic/insulated areas; avoid touching the tip with bare hands to prevent contamination or damage.
• Confirm correct fit and secure all wiring connections; test ignition on a safe flame setting after reinstalling.

This orifice directs a controlled flow of gas to the appliance burner, helping restore the correct flame size for reliable heating and ignition. Use when burner performance is weak or inconsistent to help return proper operation. What it does

• Restricts and meters gas flow to the burner for consistent flame characteristics
• Helps the burner ignite and maintain a steady flame when sized correctly
• Commonly replaces worn, clogged, or damaged orifices that cause low or irregular flames
• Resolves symptoms like weak heat, slow ignition, or uneven burner performance

• Turn off gas supply and electrical power before servicing; follow all safety precautions
• Inspect surrounding burner and sealing surfaces for debris or damage before installation
• Tighten securely but avoid overtightening; use proper fittings and thread sealant rated for gas if required

This orifice spud controls gas flow to a stove or range burner so the flame lights reliably and burns evenly. It's a small but critical gas-delivery fitting for proper burner performance. What it does:

• Directs and meters gas from the valve to the burner for a steady flame
• Restores normal ignition when a damaged spud causes weak or uneven flames
• Helps correct burners that stay low or fail to sustain a flame
• Works with the burner and valve assembly to maintain consistent heat output

• Turn off gas supply and power to the appliance before servicing
• Replace only with the exact part number or verified equivalent for safe operation
• Thread by hand then tighten to manufacturer torque—do not overtighten
• After installation, check for leaks with a safe leak-detection method;

This door insulation replaces the foam panel inside a refrigerator or freezer door to help maintain proper internal temperatures and improve energy efficiency. It restores the thermal barrier behind the inner door panel for more consistent cooling. What it does:

• Replaces the foam thermal barrier inside the door to help keep cold air in and warm air out
• Helps reduce frost buildup and uneven cooling caused by damaged or missing insulation
• Supports gasket sealing by filling the cavity behind the inner door liner
• Can reduce run-time caused by air leakage around a compromised door

• One door insulation panel

• Disconnect power before starting and work with the appliance empty and doors open
• Remove the inner door liner or access panel to access the insulation cavity
• Handle edges and metal parts carefully; wear gloves and eye protection
• Only use OEM-specified fasteners and replace any damaged clips or sealing foam as needed