Parts for Electrolux FGGF304DPFB: 02 - Backguard Parts

The Spark Module Kit is an OEM part for Frigidaire ranges. This kit includes the spark module and necessary components for installation, responsible for providing the electrical spark needed to ignite the gas burners on the stove.

Common causes of a bad spark module include electrical faults, wear and tear from regular use, or damage from power surges.

Symptoms of a bad spark module include:

• Burners not igniting
• Weak or inconsistent sparks
• Clicking sound without burner ignition
• Only some burners igniting

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board is an OEM part for Frigidaire ranges. It governs all surface heating elements, temperature settings, timers and safety functions through electronic controls.

Causes of a bad control board can include moisture damage accumulating over years of use, defects due to past power surges, or loose connections within the circuitry.

Symptoms of a bad control board include:

• Erratic or unresponsive heating element operation
• Buttons not functioning or inaccurate temperature display
• Frequent error codes triggering lockouts
• Inability to regulate power to heating elements

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement control knob restores a secure, easy-to-read interface for adjusting your appliance's settings. It lets you smoothly turn the control shaft to select heat or function when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the control shaft to turn functions on/off and adjust settings
• Provides a firm grip and clear pointer for accurate selection
• Common symptoms include a cracked knob, worn or missing indicator, loose/wobbly fit, slipping, or falling off
• Helps ensure the control returns to and indicates Off correctly when fully seated

• One control knob

• Allow the appliance to cool; for safety, disconnect power or shut off gas if applicable
• Pull the old knob straight off the control shaft—do not twist the shaft
• Align the keyed/flat side of the hub with the shaft and press the new knob on until fully seated
• Verify the pointer aligns with Off and turns smoothly; transfer any reusable insert/adapter from the original knob if your model uses one
• Some models use position-specific knobs; match markings and part number to your original

This transformer supplies the low-voltage power needed by an appliance's control system so the user interface and control board operate correctly. Replaces a worn or failed transformer to restore proper control voltage and reliable operation. What it does:

• Converts incoming line voltage to the lower control voltage used by the appliance's control board and display.
• Common symptom: control panel or display is dim, blank, or intermittently responsive.
• Common symptom: control functions (timers, cycles, lights) fail or reset unexpectedly.
• Helps stabilize control voltage to prevent erratic electronic behavior.

• One transformer

• Disconnect all power (unplug or shut off breaker) before accessing internal components.
• Observe proper wiring and polarity; match connections to the original transformer and secure terminal fasteners.
• Use appropriate mounting hardware and strain reliefs; avoid pinching or exposing wires.

This wiring harness is the OEM-style electrical connector assembly that routes power and signals between components for proper appliance operation. Replacing a damaged harness restores reliable electrical connections and function. What it does:

• Provides the bundled wires and connectors that link controls, motors and sensors
• Replaces frayed, burned or disconnected wiring that can cause intermittent operation or no power
• Restores secure, correct connections to help prevent arcing or short circuits
• Used when connectors are broken, pins are bent, or insulation is damaged

• Always disconnect power (unplug appliance or switch off breaker) before starting work
• Compare new harness to the old one and follow the appliance wiring diagram for routing and connections
• Use proper connector seating and secure harness with original clips or fasteners to avoid pinch points
• If you find melted connectors or significant damage, inspect associated components and replace as needed

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.