Parts for Electrolux FGGF3058RFA: 02 - Backguard Parts

Shield for electric ranges. Protects internal components from heat and debris. Replace if cracked, bent, or missing to maintain proper coverage.

Replace your gas range heat shield if it's cracked, warped, or missing. This protective shield installs between burner components to guard against heat damage.

This replacement panel forms the finished control area of your appliance. It provides a sturdy mounting surface for the user interface and protects the electronics behind it, restoring proper alignment, appearance, and protection when the original panel is damaged. What it does:

• Covers and protects the control compartment and wiring
• Provides mounting points for the control board, switches, knobs, and/or overlay
• Keeps controls aligned and secure for proper operation
• Common signs it's needed: dents, cracks, broken tabs, sharp edges, or controls that won't sit flush or stay secured

• One panel

• Disconnect power at the breaker; shut off gas supply if applicable
• Wear cut-resistant gloves—panel edges can be sharp
• Transfer existing control components, brackets, and hardware from the old panel to the new one; label wires or take photos for reference
• All screws and harness connections are secure before restoring power and testing

The Control Board is an OEM part for Frigidaire ranges. This part manages and regulates the functions of the range, including the oven temperature, cooking modes, and timing, ensuring precise control and efficient operation.

Causes of a bad control board can include electrical surges, overheating, or component failures due to regular wear and tear.  

Symptoms of a bad Control Board include:

• The range or oven not powering on
• Inaccurate temperature settings
• The display showing error codes or not functioning properly
• Unresponsive or malfunctioning buttons and controls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement overlay for range touch pad control panel. Installs over the control board buttons. Replace if cracked, peeling, worn, or labels are faded or illegible.

Trim cap for electric ranges. Covers and finishes control panel or body edges. Replace if cracked, broken, discolored, or missing for a complete look.

Replacement control knob for your range or cooktop. Attaches to the control shaft to adjust heat and function settings. Order when original is cracked, broken, or missing.

This is the manifold panel that mounts behind the cooktop burner knobs on a gas range. It houses the gas valve connections and provides a finished surface at the front or rear of the cooktop area. Replace this panel if it is cracked, warped, corroded, or if the mounting points for the gas valves are damaged.

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

Shield for gas ranges. Protects internal components from heat and debris. Replace if cracked, bent, or missing to maintain proper appliance protection.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.