Parts for Frigidaire CFGS365FC3: 03 - Backguard Parts

Replaces the touch pad console panel on your range. This front panel houses the control interface and typically needs replacement when dented or damaged.

This front control panel replaces a worn or damaged console face to restore button access and the appliance's user interface. It provides the visible button surface and mounting points for the console assembly. What it does:

• Replaces the appliance's front control surface so buttons and display openings are usable
• Restores worn, cracked, or cosmetically damaged console areas
• Common symptom fixes: unresponsive or missing buttons, cracked panel, or faded markings
• Works with existing internal switches and electronics when those components are intact

• Disconnect power to the appliance before starting any repair to avoid shock
• Remove the console or trim to access mounting screws and clips
• Handle carefully to avoid scratching the finished surface and bending mounting tabs
• If buttons or electronics remain nonfunctional after panel replacement, inspect or replace the internal switch board separately

Control panel plate for gas ranges. Replaces scratched, dented, or discolored front panels. Installs on the top control area to restore appearance.

This electronic clock timer assembly controls the oven clock, timed bake/broil functions, and display on compatible electric ranges and ovens. It restores timed cooking and clock display so your appliance runs on schedule. What it does:

• Replaces the oven's clock and timer control so you can set the clock, cooking timers, and delayed bake functions
• Restores a blank or unresponsive clock display and nonworking timer functions
• Helps resolve symptoms where the timer won't count down, delayed start doesn't engage, or clock settings won't hold
• Works with the range/oven's control panel to manage timed cycle operations

• One clock timer assembly

• Always disconnect power at the breaker or unplug the appliance before starting work
• Handle the control assembly carefully to avoid damage to the display, connectors, or glass/control surface
• Verify connector orientation and seating before restoring power; test clock and timer functions after installation

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replace your worn, cracked, or missing range trim. This cosmetic finishing piece installs around the edges or front panel to restore your range's appearance.

This is a replacement refrigerator door gasket that restores the seal around the door to help maintain proper temperature and efficiency. It's a direct-fit sealing strip designed to replace a worn, torn, or deformed door seal. What it does:

• Seals the gap between the door and cabinet to help keep cold air in and warm air out
• Helps reduce frost buildup and prevents moisture and leaks around the door
• Restores consistent internal temperature for better food preservation
• Reduces compressor run time caused by an improper door seal

• One refrigerator door gasket

• Recommended: replace gasket on a clean, dry door surface; remove old gasket and adhesive residue before installing
• Use the manufacturer's recommended attachment method (snap-in or adhesive) for your model
• Inspect hinge alignment and door fit before finalizing gasket installation to ensure an even seal
• For safety, unplug the appliance or disconnect power before beginning repairs

Hex nut for gas range assembly. Secures components throughout your range. Replace if stripped, corroded, or missing during repairs or maintenance.

This wiring diagram is the replacement schematic label that shows the appliance's electrical circuits and connector locations for service reference. It helps technicians and owners read wire colors, terminal IDs, and routing to diagnose electrical issues. What it does:

• Provides the factory wiring schematic and terminal/key legends for accurate troubleshooting
• Helps identify wire colors, connector positions, and component interconnections
• Useful when the original label is missing, faded, or damaged and circuit information is unreadable
• Assists in verifying proper wiring during repairs or after component replacement

• Disconnect power to the appliance before accessing the area where the label mounts
• Replace only on the documented mounting surface; clean and dry surface for adhesive labels
• Handle carefully to avoid creasing or smudging printed information

Specs: 8 - 18 x 0.500

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Adhesive overlay that covers and labels the control board buttons on your range. Replace when faded, cracked, peeling, or damaged from heat exposure.